Gendex ORTHORALIX 9200 Service Manual page 94

2.
Variable speed test.
By pressing keys kV+ and kV- on the keyboard, the step
motor is supplied with a variable speed, starting from the
lowest and reaching the highest. When the key is released,
Be careful during these two tests that the electrical
the mechanical end stop with the step motor still
rotating.
3.
Modify the movement start position.
With this procedure you can modify the start position of the
movement via software, instead of by changing the actuator
of the relevant optoswitch.
Pressing keys s+ and s- will change the number indicating
the start position (default = 0).
The correspondence between the number displayed and
the shift in mm is the following:
mm = 0.0728 X n displayed
This procedure is useful when you have to change the start posi-
tion of the C movement after having checked the system with the
image quality phantom (see the paragraph "Verify the centering
of the system with the image quality phantom" in this section).
F.4.3.5 IP address
This service program is applicable only for the Orthoralix 9200
DDE versions.
By selecting this service program it is possible to check and to
change the IP (Internet Protocol) address of the Orthoralix 9200
DDE when it is connected to the LAN network. The IP address is
made of four numbers, having a range from 0 to 255. A default
address is stored: it is possible to modify it by:
1.
pressing keys kV + and kV - for the first number on the left
2.
pressing keys mA + and mA - for the second number on the
left
3.
pressing keys s + and s - for the third number on the left
4.
pressing keys progam + and program - for the last number
The following message will appear on the display:
IP ADDRESS:
PLEASE WAIT
Gendex Dental Systems 4519-190-71193-7
F-25
Printed on: 20 Apr 2012, 04:59:40 pm; Printed by: UWE.ZELLER
ORTHORALIX 9200 Service Manual
Please take note that the address appears on the display only
when the connection to the LAN network is done properly: it takes
approximately 60 s from the system switching on and during this
time the message "PLEASE WAIT" is shown on the display.
After the modification of the IP address, to store it in the system,
press Dummy Run: for about 5 s on the display will appear "PLEASE
WAIT" and then the new IP address.
In case of PA7 board replacement, the IP address
must be stored in the new PA7 board by using this
Service Program.
F.4.3.6 Subnet mask
This service program is applicable only for the Orthoralix 9200
DDE versions.
By selecting this service program it is possible to check and to
change the Subnet Mask address of the Orthoralix 9200 DDE when
it is connected to the LAN network. The Subnet Mask address is
made of four numbers, having a range from 0 to 255. A default
address is stored: it is possible to modify it by:
1.
pressing keys kV + and kV - for the first number on the left
2.
pressing keys mA + and mA - for the second number on the
left
3.
pressing keys s + and s - for the third number on the left
4.
pressing keys progam + and program - for the last number
The following message will appear on the display:
SUBNET MASK:
PLEASE WAIT
Please take note that the address appears on the display only
when the connection to the LAN network is done properly: it takes
approximately 60 s from the system switching on and during this
time the message "PLEASE WAIT" is shown on the display.
After the modification of the Subnet Mask address, to store it in
the system, press Dummy Run: for about 5 s on the display will
appear "PLEASE WAIT" and then the new Subnet Mask address.
address must be stored in the new PA7 board by
using this Service Program.
(04.0)E