Ikegami UHL-43 Operation Manual page 42

5 Camera Setting and Adjustment
Menu Item
ETHERNET(E)
― GROUP ID
― DEVICE ID
― DEVICE NAME
― IP ADDRESS
― IP ADDRESS
― SUBNET MASK
― DEFAULT GATEWAY
― SPEED/DUPLEX
― SET
― UDP CONTROL
― ICCP PORT NO
― ICNP PORT NOR
― MASTER
― PRIMARY
― IP ADDRESS
― ICNP PORT NO
― SECONDARY
― IP ADDRESS
― ICNP PORT NO
CAMERA ID SETUP （ E ）
― PROGRAM NO. （ E ）
CAM STATUS NAME SET(E)
― FILTER NAME
― ND
― 1:
― 2:
― 3:
― 4:
― 5:
― CC
― A:
― B:
― C:
― D:
― E:
― GAMMA NAME
― CUSTOM GAMMA:
― 1:
― 2:
― 3:
― 4:
― 5:
― MATRIX NAME
― MATRIX SELECT:
― OFF:
― BT.709:
― SMPTE:
― EBU:
― BT.2020
― USER1
― USER2
32
Initial
Setting value
setting
0 0 to 99
1 1 to 99
(-------------
16 characters
---)
192.168.1.100 0.0.0.0. to 255.255.255.255
255.255.255.0 0.0.0.0. to 255.255.255.255
0.0.0.0 0.0.0.0. to 255.255.255.255
AUTO NEGOTIATION,
AUTO
10M HALF, 10M FULL,
NEGOTIATION
100M HALF, 100M FULL
REBOOT CANCEL,
READY
REBOOT EXECUTE
50001 0 to 65535
50002 0 to 65535
DISABLE DISABLE, ENABLE
192.168.1.220 0.0.0.0. to 255.255.255.255
50002 0 to 65535
DISABLE DISABLE, ENABLE
192.168.1.140 0.0.0.0. to 255.255.255.255
50002 0 to 65535
1 1 to 99, OFF
1
2
1, 2, 3, 4, 5, 1/4, 1/8, 1/16,
3
4
5
A
B
A, B, C, D, E, 3200K,
C 4300K, 6300K, CROSS,
CUSTM
D
E
DEFAULT DEFAULT, CUSTOM
CST1
CST2
CST3
CST4
HLG
DEFAULT DEFAULT, CUSTOM
OFF
709
SMPTE
EBU
2020
USER1
USER2
UHL-43 2005 VER1 (E)
Description, Remarks
Sets the ETHERNET settings.
Sets the GROUP ID of the camera for ICNP.
Sets the DEVICE ID of the camera for ICNP.
Allows the user to name the camera for ICNP.
Sets the IP address of the camera for network control.
Sets the SUBNET MASK for the IP ADDRESS of the camera.
Sets the DEFAULT GATEWAY for the IP ADDRESS of the camera.
Sets the communication method and speed for Ethernet camera control.
Executes the IP ADDRESS settings preset above.
Sets the port number for ICCP.
Sets the port number for ICNP.
Enable primary device via ICNP.
Sets the IP ADDRESS corresponding to primary device.
Sets the port number for primary device.
Enable a secondary device via ICNP.
Sets the IP ADDRESS corresponding to secondary device.
Sets the port number for secondary device.
Sets the camera No. at the time of program operation, etc. If the display of the
camera No. is set on the OCP side, the set ID No. is displayed. If the camera No.
is set on the camera side, the set ID No. is displayed on OCP.
Sets the name of ND filters.
Sets th name of ND filters.
The name can be customized in mode CUSTM(custom).
Sets the name of CC filters.
Sets th name of CC filters.
Name can be customized in mode CUSTM(custom).
Sets the name of Gamma setting.
Selects the default name or custom name of Gamma.
The name can be customized in mode CUSTOM.
Selects the default name or custom name of Matrix.
The name can be customized in mode CUSTOM.
<< SYSTEM continues to the next page >>
<< SYSTEM continued >>