Ikegami UHL-43 Operation Manual page 41

■ ⑫ SYSTEM
Menu Item
SDI OUT FORMAT
IMGAE SIZE
―
FREQ&SCAN
―
― SAMPLING
― MAPPING
― QUAD OUTPUT
― FORMAT CHANGE
MON OUT FORMAT
― IMGAE SIZE
― FREQ&SCAN
― SAMPLING
― MAPPING
― FORMAT CHANGE
H PHASE
V PHASE
FILTER SERVO CONT
BATT WARN VOLT
SYSTEM MODE
CONTROL SETTING [REMOTE]
― PROTOCOL
― ISCP INTERFACE
― ISCP BAUDRATE
― ISCP LOGE
― RESET LOG
― COMM LOG
― LOG RUN
Initial
Setting value
setting
3840x2160 / 1920x1080 /
1920x1080
1280x720
59.94P / 29.97P / 29.97PsF
/ 23.98P / 23.98PsF /
50P / 25P / 25PsF / 24P /
59.94P
24PsF /
59.94I / 50I /
119.88I / 100I
YCbCr 4:2:2 YCbCr 422 / RGB 444
3G-SDI LVL-A / 3G-SDI
3G-SDI
LVL-B / HD-SDI / EVS
LVL-A
SL
3G QL 2SI / 3G QL SQD /
3G QL 2SI
HD QL SQD
READY EXECUTE / CANCEL
1920x1080 / 1280x720
1920x1080
(Information display)
59.94I
YCbCr 422 (Information
YCbCr 4:2:2
display)
HD-SDI / 3G-SDI LVL-A
HD-SDI
(Information display)
READY EXECUTE / CANCEL
0.0 -100 to +100
0 − 562 to 2249
SERVO SERVO , MANUAL
11.0V 11.0 to 17.0V
ON ON, OFF
ICCP ICCP, ISCP
422A 422A, TTL
1200, 2400, 4800, 9600,
9600
19200
READY CANCEL, EXECUTE
0 0 to 82
START START, STOP
UHL-43 2005 VER1 (E)
5 Camera Setting and Adjustment
Description, Remarks
Selects IMAGE SIZE.
Selects the frame rate and scanning method.
Selects the sampling method.
Selects the SDI mapping.
Selects the 4K QUAD output method.
Sets the above settings.
Selects video output of MONITOR OUTPUT.
Display the IMAGE SIZE.
Selects the frame rate and scanning method.
Display the sampling method.
Display the SDI mapping.
Sets the above settings.
Matches the phase of internal synchronization signals with the phase of external
synchronization signals. The internal synchronization goes forward in "-"
direction and delays with "+" direction compared to external synchronization.
Matches the phase of internal synchronization signals with the phase of external
synchronization signals. The internal synchronization goes forward in "-"
direction and delays with "+" direction compared to external synchronization.
SERVO : Sets to the automatic control.
MANUAL : Sets to the manual control.
Sets the battery voltage value that issues the warning.
Sets the setting of camera when remote controller is disconnected.
ON : Camera holds settings.
Auto Iris does not turn on automatically.
OFF : Camera does not hold settings.
Auto iris turns on automatically.
Sets the setting for optional REMOTE connector.
Selects protocol for optional REMOTE connector.
Selects the interfce of ISCP.
Sets the baud rate of ISCP.
Sets the setting of ISCP LOG.
Resets the LOG of ISCP.
Sets the display number of ISCP LOG data.
Starts the recording of LOG.
<< SYSTEM continues to the next page >>
31