Table of Contents
Advertisement
Timer/Counter Interrupt Mask
Register – TIMSK
Timer/Counter Interrupt FLAG
Register – TIFR
AT90S2313
24
Bit
7
6
$39 ($59)
TOIE1
OCIE1A
Read/Write
R/W
R/W
Initial value
0
0
• Bit 7 – TOIE1: Timer/Counter1 Overflow Interrupt Enable
When the TOIE1 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Overflow Interrupt is enabled. The corresponding interrupt (at vector
$005) is executed if an overflow in Timer/Counter1 occurs (i.e., when the TOV1 bit is set
in the Timer/Counter Interrupt Flag Register [TIFR]).
• Bit 6 – OCIE1A: Timer/Counter1 Output Compare Match Interrupt Enable
When the OCIE1A bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Compare Match Interrupt is enabled. The corresponding interrupt (at
vector $004) is executed if a compare match in Timer/Counter1 occurs (i.e., when the
OCF1A bit is set in the Timer/Counter Interrupt Flag Register [TIFR]).
• Bit 5,4 – Res: Reserved Bits
These bits are reserved bits in the AT90S2313 and always read as zero.
• Bit 3 – TICIE1: Timer/Counter1 Input Capture Interrupt Enable
When the TICIE1 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Input Capture Event Interrupt is enabled. The corresponding interrupt
(at vector $003) is executed if a capture-triggering event occurs on PD6(ICP) (i.e., when
the ICF1 bit is set in the Timer/Counter Interrupt Flag Register [TIFR]).
• Bit 2 – Res: Reserved Bit
This bit is a reserved bit in the AT90S2313 and always reads as zero.
• Bit 1 – TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter0 Overflow Interrupt is enabled. The corresponding interrupt (at vector
$006) is executed if an overflow in Timer/Counter0 occurs (i.e., when the TOV0 bit is set
in the Timer/Counter Interrupt Flag Register [TIFR]).
• Bit 0 – Res: Reserved Bit
This bit is a reserved bit in the AT90S2313 and always read as zero.
Bit
7
6
$38 ($58)
TOV1
OCF1A
Read/Write
R/W
R/W
Initial value
0
0
• Bit 7 – TOV1: Timer/Counter1 Overflow Flag
The TOV1 is set (one) when an overflow occurs in Timer/Counter1. TOV1 is cleared by
hardware when executing the corresponding interrupt handling vector. Alternatively,
TOV1 is cleared by writing a logical "1" to the flag. When the I-bit in SREG and TOIE1
(Ti mer /Counter 1 O v erfl ow Inte rr upt Enabl e) and T OV 1 ar e s et ( one ), the
Timer/Counter1 Overflow Interrupt is executed. In PWM mode, this bit is set when
Timer/Counter1 changes counting direction at $0000.
• Bit 6 – OCF1A: Output Compare Flag 1A
The OCF1A bit is set (one) when a compare match occurs between the Timer/Counter1
and the data in OCR1A (Output Compare Register1 A). OCF1A is cleared by hardware
5
4
3
–
–
TICIE1
R
R
R/W
0
0
0
5
4
3
–
–
ICF1
R
R
R/W
0
0
0
2
1
0
–
TOIE0
–
TIMSK
R
R/W
R
0
0
0
2
1
0
–
TOV0
–
TIFR
R
R/W
R
0
0
0
0839G–08/01
Advertisement
Table of Contents
