Table of Contents
Advertisement
Notes:
-
Always manually poll the 5X00 after uploading configuration changes and
verify that the uploaded information is retained at the 5X00. When configura-
tion changes are uploaded using AquaManager at the same time configuration
changes are being made by a user in the menus on the 5X00, AquaManager
uploads may not be saved depending on the timing of keystrokes at the 5X00.
-
The Run Screen must be displayed during normal operation. If the 5X00
is not at the run screen during AquaManager uploading, pressing
the 5X00 may \only save certain configuration changes.
See Chapter 5 AquaManager - page 197 and AquaManager online help for ad-
ditional information.
Timers
The 5X00 has four daily ten event timers. Timers can be configured to control vari-
ous hardware devices. In addition, there are four Feed Smart
Timers 1-4
Menus → Timers→Timer 1-4
Configure up to 40 daily timer events using the 10 events of Daily Timer systems 1-4.
Timer events occur on a daily basis until either the start time is cleared, the timer
system is disabled, or the relay is disabled. Timer icon
icon location at the Run Screen when timer relay is active .
Directions to Configure Timers 1 - 4
Please review - Use AquaManager to configure sensor systems - page 150.
1.
Install and wire timer device(s) or any networked 5X00 instrument -
page 54.
OR
Configuring the 5X00
tm
feed timers.
displays at systemwide
YSI 5X00
180
1.
Wire relay output device(s) to REM - see IOEM/REM Safety and Instal-
lation guide>Chapter 3>Step 4>Wire REM Relay Outputs.
2.
Enter Timer 1-4 menu
▲
3.
Use
Press
4.
5.
Enable and configure submenus.
at
6.
Press
Notes:
-
Timer system must be enabled in order to energize the configured timer
relay.
-
Press
-
Timer events with overlapping times occur as follows. Example - event 1 starts
at 10:15 for 25 minutes, event 2 starts at 10:25 for 25 minutes; relay turns on at
10:15, relay turns off at 10:25, relay turns on at 10:25, relay turns off at 10:50.
-
Configure "0" duration time to disable any of the 10 timer events.
-
Timers configured over 86399 seconds (seconds in a day) are not valid.
-
If a timer is active (relay energized), the timer is NOT recalculated when the
5X00 time and/or date is changed. Once a timer has been turned on, it runs
for it's configured duration and does not reset it's run time based on changes
made to 5X00 time. Example - Timer 1, event 1 is configured to come on
at 9:00am for 10 minutes. Timer relay energizes at 9:00am. At 9:05am, the
5X00 unit time is changed to 10:05am (for daylight savings adjustment). The
timer relay will de-energize after five additional minutes. Unit time will be
10:10am. The event log will reflect the unit time when the event occurred. In
this example, 9:00am for the start time and 10:10am for the end time.
-
If a timer is active (relay energized) and 5X00 is put on service hold, the relay
will not reenergize after service hold expires regardless if timer time has not
expired. There is only one "on" time for all timers. Turn the 5X00 off, then on,
to reset the timer system. A timer relay will energize for the configured time
duration and not for the remainder of time prior to service hold. Example -
timer relay 1 is configured to start at 11:00 am for one hour. Service hold is
enabled and configured for 5 minutes. The timer relay energizes at 11:00 am.
At 11:15 am, the 5X00 is put into service hold. Timer relay 1 de-energizes.
At 11:20 am, the service hold time expires. The 5X00 is power cycled and the
timer relay energizes after 30 seconds. The timer relay de-energizes at 12:20
pm and not at 12:00 pm which would have been the original off time if the
unit had not been placed in service hold.
-
Energized timer relays de-energize at downloader. The relay will reenergize
after a power cycle following the downloader if the timer system is still active.
Menus →Timers
▼
and
to scroll and highlight submenus.
to select.
to save configuration and return to Run Screen.
to display timer events.
YSI 5X00
181
Configuring the 5X00
Advertisement
Table of Contents
Troubleshooting
