Dos Odi Driver; Common Dos Odi Errors - Olicom Ethernet MCA 10/100 Adapter Manual To Operations

68
B.3 DOS ODI Driver
This text describes the possible error messages displayed by the DOS ODI driver,
OCE3XODI.COM.
Most of the error messages are listed with no further explanation as the error
message itself gives sufficient information on cause and action to take.
The DOS ODI driver can display error messages when the driver loads. The error
messages can be displayed in two ways:
"OCE3XODI- DOS-<text> or just "<text>".

Common DOS ODI Errors

OCE3XODI-DOS-1 The LSL is not loaded.
Load the LSL or see the Novell NetWare documentation.
OCE3XODI-DOS-2 The LSL has no more room for a board using Frame <<frame>>.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-3 Could not find OCE3XODI MLID to unload.
See the Novell NetWare documentation.
OCE3XODI-DOS-4 A TSR is loaded above the OCE3XODI MLID.
IPXODI, NETX or VLM are probably loaded. Unload these program before unloading OCE3XODI. See
the Novell NetWare documentation.
OCE3XODI-DOS-5 OCE3XODI MLID could not be unloaded; the operation was aborted.
As stated.
OCE3XODI-DOS-6 The adapter did not initialize. OCE3XODI did not load.
Run the DIAG program.
Contact your place of purchase if the error condition persists.
OCE3XODI-DOS-7 You need another MLID Section Heading in the NET.CFG file in
order to load the MLID again.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-8 A NET.CFG is required to load the MLID again.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-9 The NET.CFG entry has been ignored.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-11 The MLID does not support frame <<frame>>.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-12 The protocol keyword must have a frame type. Entry ignored.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-13 The MLID could not register Protocol ID for protocol stack
<<stack>> for frame type <<frame>>.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-14 This version of LSL is not supported.
Use v. 2.14 or higher.
OCE3XODI-DOS-15 The frame type is already activated for frame <<frame>>.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-16 The node address was incorrectly specified in NET.CFG.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-17 An invalid keyword was specified in NET.CFG on line <<line>>.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-18 The frame type specified in the NET.CFG is not supported.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
OCE3XODI-DOS-19 An invalid Ethernet node address is specified in NET.CFG. The
MLID modified the incorrect address bits.
Locate and fix the error in NET.CFG. See also the NetWare documentation.
Ethernet MCA 10/100 Adapter v. 1.0, P/N: 710001414 Driver Messages