Table Of Contents - Lenze 9300 Series System Manual

5.6 Control terminals
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.7 Wiring of the system bus (CAN)
5.8 Wiring of the feedback system
5.8.1
5.8.2
5.8.3
5.9 Wiring of digital frequency input / digital frequency output
5.10 Communication modules
6 Commissioning
6.1 Before switching on
6.2 Selection of the correct operating mode
6.3 Parameter setting with the XT EMZ9371BC keypad
6.3.1
6.3.2
6.4 Controller inhibit
6.5 Changing the assignment of the control terminals X5 and X6
6.5.1
6.5.2
6.5.3
6.5.4
6.6 Adjusting the motor
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
6.6.6
6.7 Setting the speed feedback
6.7.1
6.7.2
6.8 Operating mode
6.8.1
6.8.2
6.9 Switching frequency of the inverter
EDSVF9383V EN 7.1−04/2012
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection terminal of the control card
With function "Safe torque off" active
With function "Safe torque off" deactivated
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Incremental encoder with TTL level at X8
Incremental encoder with HTL level at X9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commissioning example in V/f characteristic control mode
Commissioning example in vector control mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Free configuration of digital input signals
Free configuration of digital outputs
Free configuration of analog input signals
Free configuration of analog outputs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entry of motor data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor selection list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor temperature monitoring with PTC or thermal contact
Motor temperature monitoring with KTY
Current limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic collection of motor data
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Incremental encoder with TTL level at X8
Incremental encoder with HTL level at X9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V/f characteristic control
Vector control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
l
Contents
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
5.6−1
5.6−1
5.6−3
5.6−4
5.6−7
5.6−9
5.7−1
5.8−1
5.8−1
5.8−2
5.8−3
. . . . . . 5.9−1
5.10−1
6−1
6.1−1
6.2−1
6.3−1
6.3−1
. . . . . . . . . 6.3−5
6.4−1
. . . . . . 6.5−1
6.5−1
6.5−3
6.5−4
6.5−6
6.6−1
6.6−1
6.6−4
6.6−8
6.6−10
6.6−14
6.6−15
6.7−1
6.7−2
6.7−2
6.8−1
6.8−4
6.8−8
6.9−1
iii