socomec ATyS s Instruction Manual page 13

STEP 1
Installation
Caution:
Recommended
Ok
Ensure that
orientation
the product is
installed on a
flat rigid
surface.
Door cut-out for front panel.
138
20
Ø7
Ø7
Ø9
Ø9
Example: Control wiring for a 400VAC application having a 3 phase and neutral supply.
2
R1 R2 S1 S2 T1 T2
312 313 314 315 316 317
5 4 3 2 1
ATYS p - 542001E - SOCOMEC
M
M J1
Dimensions in mm.
T U
Ok
T U
W
W
3 P
J 1
34
U
U
M 120
T 36
C 244
U 20
W 9
Ø7
W
CA 10
W
Ø9
U
STEP 2
U
W
Minimum cable section Cu (mm
(IEC 60947-1)
Recommended cable section Cu (mm
at Ith
Maximum cable section Cu (mm
Maximum Cu busbar width (mm)
Type of screw
Recommended tightening torque (N.m)
Maximum tightening torque (N.m)
LOAD
ATyS D20
Remote Control /
6 Display Unit
7 8 9
63A 64A 24 14 04 13
J1
M J1
C
T U
125 A 160 A 200 A 250 A
4 P 3 P 4 P 3 P 4 P 3 P
34 34 34 34 34 35
150 120 150 120 150 160
36 36 36 36 36 50
244 244 244 244 244 244
20 20 20 20 20 25
W
9 9 9 9 9 11
10 10 10 10 10 15
U
Power Terminal Connections
To be connected using terminal lugs, rigid or flexable busbars.
FRAME B3
125 A 160 A 200 A
) at Ith
2
35 35 50
2 )
U - - -
) 50 95 120
2
25 25 25
M8 M8 M8
8.3 8.3 8.3
13 13 13
STEP 3
CONTROL / COMMAND Terminals
Ensure that the product is in Manual Mode.
1
1 2
preferred source alternate source
1. Position 0 order
2. Position 1 order
3. Position 2 order
4. Zero position priority order
5. Remote Control Enable (Priority over Auto)
6. Product Available output (Motor)
7. Position II aux contact
8. Position I aux contact
9. Position 0 aux contact
10. O/P to ATyS D20 remote unit
11. Programmable Output Contact.
By default set to ATS Product
Available - Normally Open
C
21
21
C
315 A 400 A 500 A
4 P 3 P 4 P 3 P 4 P 3 P 4 P
35 35 35 35 35 34 34
210 160 210 160 210 210 270
50 50 50 50 50 65 65
244 244 244 244 244 320 320
25 35 35 35 35 32 32
11 11 11 11 11 13 13
15 15 15 15 15 20 20
FRAME B4
250 A 315 A 400 A 500 A
95 120 185 2x95
- - - 2x30x5
150 240 240 2x185
32 32 32 50
M10 M10 M10 M12
20 20 20 40
26 26 26 45
1
2
12-15. Programmable Inputs 1-4
16-17. Programmable Inputs 5-6
18. Aux. Supply (207/210) to be used
with ATyS optional I/O modules
19. Contact "Start/Stop Genset" : if S1
is not available the NC contact le
contact (71-72) is close
20. Contact "Start/Stop Genset" : if S1
is not available the NO contact le
contact (71-74) is open
21. Option Module Slots 1 to 4
22. Current Transformer incoming cable
connections
23. Voltage Sensing Inputs
24. Power Supply Inputs
21
630 A
3 P 4 P
34 34
210 270
65 65
320 320
45 45
13 13
20 20
FRAME B5
630 A
2x120
2x40x5
2x300
50
M12
40
45
EN 13