YASKAWA SI-EP3 Technical Manual page 27

No.
Name
(Hex.)
F6-07 Multi-Step Ref @ NetRef/
ComRef
(03A8)
F6-08 Comm Parameter Reset
@Initialize
(036A)
F6-14 BUS Error Auto Reset
(03BB)
F6-15 Comm. Option Parameters
Reload
(0B5B)
F7-01 IP Address 1
(03E5)
F7-02 IP Address 2
(03E6)
F7-03 IP Address 3
(03E7)
F7-04 IP Address 4
(03E8)
F7-05 Subnet Mask 1
(03E9)
F7-06 Subnet Mask 2
(03EA)
F7-07 Subnet Mask 3
(03EB)
YASKAWA SIEP C730600 89E PROFINET Technical Manual
In A1-02 = 2, 8 [Control Method Selection = Open Loop Vector, EZ Vector Control], this
value is read as the Torque Limit.
–CR700, CH700
In A1-02 = 2, 3, 4 [Control Method Selection = Open Loop Vector, Closed Loop Vector,
Advanced Open Loop Vector], this value is read as the Torque Limit.
–HV600
Parameter is available in A1-02 = 8 [Control Method Selection = EZ Vector Control].
In A1-02 = 8 [Control Method Selection = EZ Vector Control], this value is read as the
Torque Limit.
• If the PLC does not supply a torque reference or torque limit when F6-06 = 1 [Torque
Reference/Limit by Comm = Enabled], the motor cannot rotate.
0 : MultiStep References Disabled
1 : MultiStep References Enabled
Note:
Default setting is 1 for GA500.
Selects whether communication-related parameters F6-xx and F7-xx are set back to original
default values when you use parameter A1-03 [Initialize Parameters] to initialize the drive.
0 : No Reset - Parameters Retained
1 : Reset Back to Factory Default
Note:
The drive will not change this setting value when you set F6-08 = 1 and use A1-03 to
initialize the drive.
Enables and disables the automatic reset of a bUS [Option Communication Error] fault.
0 : Disable
1 : Enabled
Note:
This setting is available in A1000 software versions PRG: 1021 and later.
Sets how the drive will enable the F6-xx/F7-xx communication-related parameters that you
changed.
0 : Reload at Next Power Cycle
1 : Reload Now
2 : Cancel Reload Request
Note:
• F6-15 is reset to 0 after setting 1 or 2.
• Not available on 1000-series drives.
Sets the static/fixed IP address. Sets the most significant octet.
Note:
• Change the parameter then cycle power on the drive. Set F6-15 = 1 [Comm. Option
Parameters Reload = Reload Now], to have settings take effect immediately on non-1000
series drives.
• Set IP Address to F7-01 to F7-04 when F7-13 = 0. All IP Addresses must be unique.
• Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed IP address. Sets the second most significant octet.
Note:
• Change the parameter then cycle power on the drive. Set F6-15 = 1 [Comm. Option
Parameters Reload = Reload Now], to have settings take effect immediately on non-1000
series drives.
• Set IP Address to F7-01 to F7-04 when F7-13 = 0. All IP Addresses must be unique.
• Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed IP address. Sets the third most significant octet.
Note:
• Change the parameter then cycle power on the drive. Set F6-15 = 1 [Comm. Option
Parameters Reload = Reload Now], to have settings take effect immediately on non-1000
series drives.
• Set IP Address to F7-01 to F7-04 when F7-13 = 0. All IP Addresses must be unique.
• Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed IP address. Sets the fourth most significant octet.
Note:
• Change the parameter then cycle power on the drive. Set F6-15 = 1 [Comm. Option
Parameters Reload = Reload Now], to have settings take effect immediately on non-1000
series drives.
• Set IP Address to F7-01 to F7-04 when F7-13 = 0. All IP Addresses must be unique.
• Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed Subnet Mask. Sets the most significant octet.
Note:
Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed Subnet Mask. Sets the second most significant octet.
Note:
Set F7-01 to F7-12 when F7-13 = 0.
Sets the static/fixed Subnet Mask. Sets the third most significant octet.
Note:
Set F7-01 to F7-12 when F7-13 = 0.
Description
6 Related Drive Parameters
Default
(Range)
0
(0, 1)
0
(0, 1)
0
(0, 1)
0
(0 - 2)
192
(0 - 255)
168
(0 - 255)
1
(0 - 255)
20
(0 - 255)
255
(0 - 255)
255
(0 - 255)
255
(0 - 255)
27