Extron electronics IN1804 Series User Manual page 84

Command
Advanced Configuration (continued)
Contact Port Status
View individual contact port
status
View status of all contact
ports
Tally Port Status
Set individual port state
Set states of all ports
View individual tally port
status
View status of all tally ports
KEY:
X7%
= Contact/Tally port number
X7^
= Contact/Tally port state
Twisted Pair Protocol
Set input TP protocol
(IN1804 DI and DI/DO only)
View input TP protocol
Set output TP protocol
(IN1804 DO and DI/DO only)
View output TP protocol
DTP Remote Power Parameters
ATTENTION:
• Ensure that the correct remote DTP power setting is used. Sending DTP2 power to a DTP (series 1) endpoint can
result in hardware damage. Enable DTP2 power only to a compatible DTP2 endpoint.
• Assurez-vous de bien régler l'alimentation DTP à distance. L'envoi d'une alimentation DTP2 à un point de connexion
DTP (ancienne gamme) peut provoquer des dommages matériels. Assurez une alimentation DTP2 uniquement vers un
point de connexion DTP2 compatible
Set input remote power
(IN1804 DI and DI/DO only)
View input remote power
Set output remote power
(IN1804 DO and DI/DO only)
View output remote power
KEY:
X6^
= DTP remote power status
X6&
= DTP protocol setting
ASCII Command Response
(Host to Switcher) (Switcher to Host)
EX7% } X7^]
CNTC
Verbose modes 2 and 3:
Cntc
E } X7^
CNTC
•...
EX7% X7^ }
* TALY Taly
EX7^ X7^ }
... TALY
Taly
EX7% } X7^]
TALY
E } X7^
TALY •...
1
through
0
= Open,
E X6& }
I4* HDBT HdbtI4*
E } X6&]
I4HDBT
E X6& }
O1* HDBT HdbtO1*
E } X6&]
O1HDBT
E X6^ }
I4* RPWR RpwrI4*
E } X6^]
I4RPWR
E X6^ }
O1* RPWR RpwrO1*
E } X6^]
O1RPWR
0
= No remote power (default)
1
= DTP
2
= DTP2
0
= DTP format (default),
IN1804 Seamless Scaling Switchers • SIS Configuration and Control
Additional Description
View the contact status
port
X7% X7^]
*
X7^]
View status
X7% X7^]
* Set the tally output state for port
X7^
.
Set all tally ports at once to port state
X7^
.
X7^ X7^]
...
View the tally status
X7%
.
X7^]
View status
7
1
= Closed
X6&]
Set the TP protocol for input 4 to
View current TP protocol setting for input
4.
X6&]
Set the TP protocol for output 1A to
View current TP protocol setting for
output 1A.
X6^]
Set the remote power on input 4 to
View remote power setting for input 4.
X6^] Set the remote power for output 1A to
X6^
.
View remote power setting for output 1A.
1
= XTP format,
X7^
of contact
X7%
.
X7^
of all contact ports.
X7%
X7^
of contact port
X7^
of all tally ports.
X6&
2
= HDBaseT format
to
.
X6&
.
X6^
.
76