Extron electronics IN1808 Series Setup Manual

IN1808 Series • Setup Guide
The Extron IN1808 Series are eight-input seamless scaling presentation switchers that support signal resolutions up to
4K @ 60 Hz at 4:4:4. They feature DisplayPort, HDMI, and DTP2 inputs, HDMI output and a mirrored Extron DTP2 output
extension to send video, audio, and control signals up to 330 feet (100 meters) over a shielded CATx cable. The IN1808 IPCP SA
and IN1808 IPCP MA 70 models each have a built-in Extron IPCP Pro 355M IP Link Pro Control Processor, and an integrated
100 watt class D power amplifier. The IN1808 Series delivers high image quality, fast and reliable switching, Extron ProDSP audio
processing, seamless video transition effects, logo keying, and HDMI loop out. The scalers can be controlled and configured over
Ethernet, RS-232, or USB.
This guide provides instructions for an experienced user to set up and configure the IN1808 (base model), IN1808 IPCP SA,
and IN1808 IPCP MA 70 scalers. It covers how to perform basic operations using the front panel controls and selected Simple
Instruction Set (SIS™) commands.
NOTES:
For full installation, configuration, menus, connector wiring, and operation details, see the IN1806 and IN1808
•
Series User Guide at www.extron.com. For installation, configuration, and operation details of the embedded
IPCP Pro 355M, see the IPCP Pro Series User Guide.
The IN1808 Series products can also be configured via the Extron Product Configuration Software (PCS), available at
•
www.extron.com. For information on using PCS, see the IN1806 and IN1808 Series Help File.
Installation
IN1808 Series Rear Panel Connectors
Figure 1 shows the rear panel of the IN1808 IPCP SA rear panel. The IN1808 IPCP MA 70 rear panel is the same except that
the embedded amplifier is mono while the SA model amplifier is stereo. The IN1808 base model rear panel does not have an
embedded IPCP Pro 355M module (see figure 1,
IN1808 IPCP SA
2
100-240V~1.5A MAX
1 3
50-60 Hz
A B
Figure 1. Rear Panel Connectors, IN1808 IPCP SA
A
AC power connector
B
DisplayPort input connector (input 1)
C HDMI (with CEC) loop out connector
D DTP2/XTP input connectors (inputs 7
and 8)
E HDMI (with CEC) output connector (1A)
F
DTP2/XTP/HDBaseT (with CEC) output
connector (1B)
G
Over TP IR pass-through connector
NOTE: The IN1808 base model has a LAN connector to the left of the Remote RS-232 connector
R
(see in the illustration at right) instead of the AV LAN ports on the IPCP Pro 355M control
2 2
processor.
1 1 3 3
100-240V 50/60 Hz 100-240V 50/60 Hz
--A MAX --A MAX
P ) or amplifier module (
Q
R R R R R R R R R R R R R R R R R R R R R R R R
4 6
7 8
SIG LINK SIG
LOOP OUT
5
IN
INPUTS (DTP2/XTP)
C D
H
Analog line audio inputs 3 and 4
I
Analog mic/line audio inputs 1
and 2 and adjacent phantom
power LEDs
J
Analog line audio outputs 1
through 4
K
Remote RS-232 port
L
Reset LED
M Reset button
INPUTS INPUTS
DTP2/XTP II DTP2/XTP
4 4 6 6
7 7 8 8
SIG SIG LINK LINK SIG SIG
5 5
IN IN
LOOP OUT LOOP OUT
N ).
P
COM 1 COM 2 COM 3 DIGITAL I/O AV LAN 2 AV LAN 3
Tx Rx G RTS CTS Tx Rx G Tx Rx G 1 2 3 4 G
IR/SERIAL RELAYS eBUS
1 2 1 2 C 3 4 C +V -S +S G
S G S G PWR OUT = 6W LAN AV LAN 1
1A 1B
LINK SIG LINK
OVER TP
Tx Rx
HDMI/CEC
IN OUT
OUTPUTS (DTP/XTP/HDBT)
E F G
OUTPUTS OUTPUTS
DTP2/XTP/HDBT DTP2/XTP/HDBT
1A 1A 1B 1B
LINK LINK SIG SIG LINK LINK
HDMI/CEC HDMI/CEC
IN IN OUT OUT
O
N
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L R
CLASS 2 WIRING
L R 1 1 2
+48V
AUX
MIC/LINE
IR
3 4 2 3 4
+48V
G
AUDIO INPUTS OUTPUTS REMOTE
H I J KL
N
Amplified audio output (IPCP models
only)
o
Aux mono or stereo analog line
audio input connector
P
IPCP Pro 355M Control Processor
(IPCP models only)
Q
HDMI inputs 2 through 6
R
LAN connector (IN1808 base model
only, see the note and illustration
below)
AUDIO INPUTS AUDIO INPUTS OUTPUTS OUTPUTS
1 1
L L R R 1 1 2 2
+48V +48V
AUX AUX
OVER TP OVER TP MIC/LINE MIC/LINE
IR IR 2 2
3 3 4 4 3 3 4 4
+48V +48V
Tx Rx Tx Rx G G
RS-232 RESET
M
Tx Rx G
R
REMOTE REMOTE
LAN LAN
RS-232 RS-232 RESET RESET
Tx Rx Tx Rx G G
1