Table of Contents
Advertisement
Agency Listings, Approvals, and Requirements
Section 2: Agency Listings, Approvals, and Requirements
2.1 Federal Communications Commission (FCC)
The following information must be provided to the telephone company before the 6808 can be connected to the phone lines:
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the inside cover of this equipment is
a label that contains, among other information, a product identifier. If requested, this information must be provided to the telephone com-
pany.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part
68 rules and requirements adopted by the ACTA. A compliant telephone cord (not provided) and modular jack must be utilized with this
product. It is designed to be used with a modular jack that is also compliant.
The REN (ringer equivalence number) provided on this installation sheet is used to determine the number of devices that may be con-
nected to the public switched telephone network. This number must not exceed 5.0. Since this product has an REN of 1.0A, the number
of devices is limited. The REN number is embedded in the FCC registration number as 10A.
If the 6808 causes harm to the telephone network, the telephone company will notify you in advance that the temporarily discontinuance
of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main-
tain uninterrupted service.
If trouble is experienced with the 6808, for repair or warranty information, please contact Honeywell Silent Knight technical support at
800-446-6444 or www.silentknight.com. If the equipment is causing harm to the telephone network, the telephone company may request
that you disconnect the 6808 until the problem has been resolved.
This product cannot be adjusted or repaired in the field. It must be returned to the factory for service.
This equipment is not designed for use with party line service. Connection to party line service is subject to state tariffs. You may contact
the state public utility commission, public service commission or corporation commission for information.
Since the 6808 is a commercial fire alarm panel, it must be connected upstream of all other equipment utilizing the phone lines. If you
have questions about the installation, contact your telephone company or a qualified installer.
WARNING:
!
This device has been verified to comply with FCC Rules Part 15. Operation is subject to the following conditions: (1) This device may not
cause radio interference, and (2) This device must accept any interference received, including interference that may cause undesired opera-
tion.
CAUTION:
!
To ensure proper operation, this equipment must be installed according to the enclosed installation instructions. To verify that the equipment
is operating properly and can successfully report an alarm, this equipment must be tested immediately after installation, and periodically
thereafter, according to the enclosed test instructions.
CAUTION: IN ORDER FOR "ALARM DIALING EQUIPMENT" TO BE ABLE TO SEIZE THE PHONE LINE TO REPORT AN
ALARM OR OTHER EVENT WHEN OTHER CUSTOMER EQUIPMENT (TELEPHONE, ANSWERING SYSTEM, COMPUTER
MODEM, ETC.) CONNECTED TO THE SAME LINE IS IN USE, "ALARM DIALING EQUIPMENT" MUST BE CONNECTED
TO A PROPERLY INSTALLED RJ31X JACK. THE RJ31X JACK MUST BE CONNECTED IN SERIES WITH, AND AHEAD
OF, ALL OTHER EQUIPMENT ATTACHED TO THE SAME PHONE LINE. SERIES INSTALLATION OF AN RJ31X JACK IS
DEPICTED IN THE FIGURE BELOW. IF YOU HAVE ANY QUESTIONS CONCERNING THESE INSTRUCTIONS, YOU
SHOULD CONSULT YOUR TELEPHONE COMPANY OR A QUALIFIED INSTALLER ABOUT INSTALLING THE
NECESSARY JACK AND ALARM DIALING EQUIPMENT FOR YOU
2.2 Underwriters Laboratories (UL)
2.2.1 Requirements for All Installations
General requirements are described in this section. When installing an individual device, refer to the specific section of the manual for
additional requirements. The following subsections list specific requirements for each type of installation (for example, Central Station
Fire Alarm systems, Local Protected Fire Alarm systems, and so on). See Section 10.6 for information on releasing operation.
1.
All field wiring must be installed in accordance with NFPA 70 National Electric Code.
14
A
Manufacturer:
B
Model Number:
C
FCC registration number:
Ringer equivalence:
D
Type of jack:
E
Facility Interface Codes:
F
Service Order Code:
Honeywell Silent Knight
6808
US: HS9AL10A2100
1.0A
RJ31X
Loop Start:
02LS2
9.0F
6808 Manual — P/N LS10146-001SK-E:C 09/28/2017
Advertisement
Table of Contents
Troubleshooting
