Honeywell 6808 Installation And Operation Manual page 24

Before You Begin Installing
5865-4 LED Annunciator
(with reset and silence switches)
5865-3 LED Annunciator
5880 LED I/O Module
5883 Relay Interface
5496 NAC Expander
5895XL Power Supply
Network Cards
SK-NIC Network Interface Card
SK-FML Fiber Optic Multi Mode
SK-FSL Fiber Optic Single Mode
A Total System Current
Auxiliary Devices
IPDACT-2 IP Communicator
IPDACT-2UD IP Communicator
CELL-MOD/CELL-CAB-SK
B Auxiliary Devices Current
Notification Appliance Circuits
5495/5499 Power Supply
C Notification Appliances Current
D Total current ratings of all devices in system (line A + line B + C)
E Total current ratings converted to amperes (line D x .001):
F Number of standby hours (24 or 60 for NFPA 72, chapter 1, 1-5.2.5):
G Multiply lines E and F.
H Alarm sounding period in hours. (For example, 5 minutes =.0833 hours)
I Multiply lines E and H.
J Add lines G and I.
Multiply by the Derating Factor
The FACP can only support 5 devices w/LED's on. This current draw has been added to the panels alarm current.
If using 24 VDC aux power only. No standby or alarm current for battery calculation if using 24 VAC, 120 VAC or 240 VAC.
If using door holders, you do not need to consider door holder current for alarm/battery standby, because power is removed during that
time. However, during normal operation, door holders draw current and must be included in the 6.0A total current that can be drawn from
the panel.
Use next size battery with capacity greater than required.
24
Number of
Device
Devices
(8 max.)
(32 max.)
(8 max.)
(1 Max.)
(1 Max.)
(1 Max.)
3
Refer to devices manual for current rating.
Refer to devices manual for current rating.
4
Table 3.3 Current Draw worksheet for SD Devices
Current per Device
Standby:
Alarm:
Standby:
Alarm:
Standby:
Alarm:
Standby:
Alarm:
(22 mA per relay)
Standby/Alarm:
Standby/Alarm:
Standby/Alarm:
Standby/Alarm:
Standby/Alarm:
Alarm:
Standby:
Alarm:
Standby:
Standby:
Alarm:
Alarm/Standby:
Alarm/Standby:
Alarm/Standby:
24 VDC One input circuit:
Both input circuits:
Alarm:
Alarm:
Alarm:
Alarm:
Total standby AH
Total alarm AH
Total ampere hours
required
6808 Manual — P/N LS10146-001SK-E:C 09/28/2017
Standby Alarm
Current Current
35 mA mA
145 mA mA
35 mA mA
145 mA mA
35 mA mA
200 mA mA
0 mA mA
220 mA mA
10 mA mA mA
10 mA mA mA
21 mA mA mA
53 mA mA mA
79 mA mA mA
136 mA mA
93 mA mA
155 mA mA
98 mA mA
55 mA mA
100 mA mA
mA mA mA
mA mA mA
mA mA mA
15 mA mA
30 mA mA
mA mA
mA mA
mA mA
mA mA
mA
mA mA
A A
H
AH
H
AH
AH
x 1.25