Assa Abloy SARGENT Profile Series Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Assa Abloy Manuals
  4. Door locks
  5. SARGENT Profile Series
  6. Installation instructions manual
Assa Abloy SARGENT Profile Series Installation Instructions Manual

Assa Abloy SARGENT Profile Series Installation Instructions Manual

V.s2 wifi exit device
Hide thumbs Also See for SARGENT Profile Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction and Installation Manual
A7787F
01/18
Copyright 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
v.S2
Profile
WiFi Exit Device

Installation Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SARGENT Profile Series and is the answer not in the manual?

Questions and answers

Related Manuals for Assa Abloy SARGENT Profile Series

Summary of Contents for Assa Abloy SARGENT Profile Series

  • Page 1: Installation Instructions

    Profile WiFi Exit Device Installation Instructions A7787F 01/18 Copyright 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

  • Page 2: Table Of Contents

    Installation for v.S2 With 8877/8878 Rim Exit ......9 Installation for v.S2 With 8977/8978 Mortise Exit Device ..16 Operational Check ..............24 Changes or modifications to this unit not expressly approved by ASSA ABLOY Inc. Warning could void the user’s authority to operate the equipment.

  • Page 3: General Description

    Profile Series v.S2 WiFi Exit Device General Description The SARGENT Profile Series v.S2 Exit Device is available with either an HID® 125 kHz Prox or 13.56 MHz iCLASS® technology reader. Either can be used in applications requiring wireless access control. The v.S2 is a self-contained microprocessor-controlled access control product with non-volatile memory.

  • Page 4: Lock Wiring

    Profile Series v.S2 WiFi Exit Device Lock Wiring Controller Board Connectors (Inside Escutcheon) COM (VIOLET) NC (PINK) (RX) To Spade Connector Unused (Attached to Lower Left Screw From of Controller) From Chassis Trim Ground to Screw A7787F...

  • Page 5: Parts Breakdown

    Profile Series v.S2 WiFi With Rim Exit Device Parts Breakdown for v.S2 With 8877/8878 Rim Exit Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS (8877/8878 x ET x Lever Design) A7787F...
  • Page 6 Profile Series v.S2 WiFi With Rim Exit Device Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS, Continued (8877/8878 x ET x Lever Design) PART NO. DESCRIPTION REQ’D ITEM S2-777- 8-HAND-FINISH ’S’ Series ET Trim - With Cylinder S2-778-8-HAND-FINISH ’S’...
  • Page 7 Profile Series v.S2 WiFi With Mortise Exit Device Parts Breakdown for v.S2 With 8977/8978 Mortise Exit Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS (8977/8978 x ET x Lever Design) A7787F...
  • Page 8 Profile Series v.S2 WiFi With Mortise Exit Device Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS, Continued (8977/8978 x ET x Lever Design) ITEM PART NO. DESCRIPTION REQ’D S2-777-HAND-FINISH ’S’ Series ET Trim - With Cylinder S2-778-HAND-FINISH ’S’...

  • Page 9: Installation For V.s2 With 8877/8878 Rim Exit

    Profile Series v.S2 WiFi With Rim Exit Device Installation for Profile Series v.S2 With 8877/8878 Rim Exit Device 1 – Prepare Door Inside A. Verify Hand and Bevel of Door • This device is non-handed. • Door should be fitted and hung. •...
  • Page 10 Profile Series v.S2 WiFi With Rim Exit Device 3 – Secure Inside Trim and Chassis 1. Route ET harness through wire run channel for wood doors (Fig. 3A) and through access hole for metal doors (not shown). Note: Make sure no wires are pinched. 2.
  • Page 11 Profile Series v.S2 WiFi With Rim Exit Device 4 – Install Cylinder For devices without cylinder, skip this step. 1. Insert cylinder into ET trim (Fig. 4A). 2. Mate cylinder tailpiece into hub of exit device chassis. 3. Make sure ET harness is clear of cylinder and cylinder tailpiece. Fig.
  • Page 12 Profile Series v.S2 WiFi With Rim Exit Device 7 – Install Door Position Switch (DPS) If it isn’t installed, install the door position switch: 1. Prep door according to proper template (A7992). 2. Insert DPS into the raceway on the latch edge of the door by |pushing wires down raceway towards the lock.
  • Page 13 Profile Series v.S2 WiFi With Rim Exit Device 9 – Connect and Position Outside Escutcheon Wires Images shown represent installation without gasket. If gasket is necessary, refer to 8 – Attach Gasket and Install Outside Escutcheon. Before the controller is attached to the door: 1.
  • Page 14 Profile Series v.S2 WiFi With Rim Exit Device 11 – Connect and Position Chassis Wires 1. Connect RX rail connector from ET to chassis harness. 2. Attach connector from ET to the controller assembly (TB1). Tuck ferrite bead under circuit board. 3.
  • Page 15 Profile Series v.S2 WiFi With Rim Exit Device 13 – Install (or Replace) Batteries IMPORTANT: Do not install batteries if controller is powered by external power supply To install the batteries, first remove the battery cover Battery using the security tool provided (Fig. 13A). Cover 4.

  • Page 16: Installation For V.s2 With 8977/8978 Mortise Exit Device

    Profile Series v.S2 WiFi With Mortise Exit Device Installation for Profie Series v.S2 With 8977/8978 Mortise Exit Device Inside 1 - Prepare Door A. Verify Hand and Bevel of Door • Check handing of door - this device is not reversible •...
  • Page 17 Profile Series v.S2 WiFi With Mortise Exit Device 4 – Secure Inside Trim and Chassis 1. Route ET harness through wire route slot for wood doors (Fig. 4A) and access hole for metal doors (not shown). Note: Make sure no wires are pinched. 2.
  • Page 18 Profile Series v.S2 WiFi With Mortise Exit Device 5 - Install Exit Chassis 1. Route ET harness through wire run channel for wood doors (Fig. 5A) and through access hole for metal doors (not shown). 2. Mount exit chassis carefully. Do not pinch harness wires. 3.
  • Page 19 Profile Series v.S2 WiFi With Mortise Exit Device 7 – Door Options A. Fire Stop Plate (P/N 52-0033) Fire-rated doors require a fire stop plate on the outside of the door (Fig. 7A). 1. If not present, drill (2) 1/8" x 1-1/4" deep Ribbon Cable Hole holes in the door.
  • Page 20 Profile Series v.S2 WiFi With Mortise Exit Device 9 – Install Gasket and Outside Escutcheon For exterior applications, use a gasket (part number 82-0500) between escutcheon and outside door surface. Gasket 82-0500 To apply weatherseal gasket: Carefully remove the backing from the gasket (Fig. 9A). 2A.
  • Page 21 Profile Series v.S2 WiFi With Mortise Exit Device 10 – Connect and Position Outside Escutcheon Wires Images shown represent installation without gasket. If gasket is necessary, refer to 9 – Install Gasket and Outside Escutcheon. Before the controller is attached to the door: 1.
  • Page 22 Profile Series v.S2 WiFi With Mortise Exit Device 12 – Additional Chassis Wiring Connections Chassis, DPS and raceway wire connections: 1. Connect RX rail connector from ET to chassis harness. 2. Attach connector from ET to the controller assembly (TB1). Tuck ferrite bead under circuit board.
  • Page 23 Profile Series v.S2 WiFi With Mortise Exit Device 14 – Install (or Replace) Batteries IMPORTANT: Do not install batteries if controller is powered by external power supply. 1. To install the batteries, first remove the battery cover using the security tool provided (Fig. 14A). Battery Cover 2.

  • Page 24: Operational Check

    The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2017, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Table of Contents