Leave components (reader and controller) protected in their respective anti-static bags until ready for installation • Do not touch pins, leads or solder connections on the circuit boards For specific security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-9473. A8208-5 • 800-810-9473 • www.sargentlock.com...
IN100 Series Exit Device Product & Technical Specifications Operating temperature: -13°F (-25°C) to 151°F (66°C) Humidity: < 85% non-condensing Input Power: DC 9V, 1.5A (6 AA alkaline batteries) Optional hard-power 12-24VDC, 1.0A Reader with multiCLASS SE technology offers support for the following credentials: ®...
IN100 Series Exit Device Product Illustrations NOTE: Escape Return functionality is not available with IN100 8800/PE8800 Series Consult document A8367 for specific part numbers ITEM No. DESCRIPTION Aperio Reader Assembly Mounting Plate Assembly (includes gasket) Aperio Controller AA alkaline batteries (6) Branded Battery Cover Assembly with Privacy Button *8877/PE8877, 8878/PE8878, 8977/PE8977, 8978/PE8978 (example: IN-100-EM01PE8877-IP-B) To comply with “Fire Listed”...
Page 6
IN100 Series Exit Device 8800 & PE8800 Product Illustrations (Continued) 77 / 78 Function x Trim x Lever Design IN100 Rim Exit Device Consult document A8367 for specific part numbers ITEM DESCRIPTION REQ’D Cylinder Assembly (Reference Catalog for Available Cylinders) Lever (Reference Catalog for Available Styles) Exit Trim With Cylinder Exit Trim Without Cylinder...
Page 7
IN100 Series Exit Device 8800 & PE8800 Product Illustrations (Continued) 77 / 78 Function x Trim x Lever Design IN100 Mortise Exit Device See document A8367 for part numbers ITEM DESCRIPTION REQ’D Cylinder Assembly (Reference Catalog for Available Cylinders) Lever (Reference Catalog for Available Styles) Exit Trim With Cylinder Exit Trim Without Cylinder Motor Actuator Assembly...
Page 8
IN100 Series Exit Device PE8600 Product Illustrations (Continued) PE8600 Concealed Vertical Rod (CVR) Exit Device (78 Function) Prior to installation, please confirm receipt of all parts See document A8367 for part numbers ITEM Description Req. Chassis Wood Door (WD) Screw Pack Chassis Metal Door (MD) Screw Pack (not shown) WD Top Assembly MD/Aluminum Door (AD) Top Assembly (not shown)
Page 9
IN100 Series Exit Device PE8700 Product Illustrations (Continued) PE8700 Surface Vertical Rod (SVR) Exit Device (78 Function) Top Rod (consult factory) Guide for Rod Screw Pack for Guide and Covers Bottom Rod (consult factory) Case Assembly Cover Trim (Trim with gasket shown) Chassis Assembly LHRB Chassis Assembly RHRB Rod Adjustment Pin...
IN100 Series Exit Device 8800 & PE8800 Installation Instructions Rim Exit Device 1. Prepare door. a. Verify hand and bevel of door. (Figure 1) NOTE: Stand on outside of locked door when determining door hand. Inside b. Verify exit device is correct hand for door. c.
Page 11
IN100 Series Exit Device 8800 & PE8800 Installation Instructions Rim Exit Device (Continued) 2. Install door position switch. NOTE: Wood doors have 3/8" raceway to con- troller cutout and metal doors have 3/4" race- way to controller cutout. a. Refer to template A8214 (80 Series) or MEFT18 (PE80 Series).
Page 12
IN100 Series Exit Device 8800 & PE8800 Installation Instructions Rim Exit Device (Continued) 3. Mount exit device chassis. NOTE: Exit chassis harness consists of a 6-pin female connector and ground Inside of wire/terminal. (Figure 5) Door a. Feed 6-pin connector and larger ground lug straight through to outside of door.
Page 13
IN100 Series Exit Device 8800 & PE8800 Installation Instructions Rim Exit Device (Continued) For devices without cylinder, go to Step 6. 5. Install cylinder. (Figures 9, 10) a. While installing rim cylinder, support tail piece of cylinder, verifying its engagement with top hub of exit chassis.
Page 14
IN100 Series Exit Device 8800 & PE8800 Installation Instructions Rim Exit Device (Continued) Install rail assembly. (Figure 11) a. Retrieve harness from end of rail. Harness has limited travel and can be damaged. b. Attach harness to female connector on chassis. c.
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device Inside Prepare door. a. Verify hand and bevel of door. (Figure 12) NOTE: This exit device is handed and is not reversible. Left Hand Right Hand Reverse Reverse b.
Page 16
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device (Continued) Install door position switch. NOTE: Wood doors have 3/8" raceway to controller cutout and metal doors have 3/4" raceway to controller cutout. a. Refer to template A8215 (80 Series) or (Door Position MEFT10 (PE80 Series).
Page 17
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device (Continued) Mount mortise and exit device chassis. a. Slide mortise lock into door and loosely secure with two (2) flat head screws. NOTE: Exit chassis harness consists of a 6-pin female connector and ground wire/terminal. (Figure 16) b.
Page 18
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device (Continued) Position exit trim. (Figure 17) NOTE: For exterior applications, use trim gasket to seal between trim escutcheon and outside door surface. a. Connect motor harness adapter to chassis harness connector. b.
Page 19
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device (Continued) 5. For devices without cylinder, go to Step 6. a. Secure cylinder by threading into lockbody. b. After cylinder is installed, tighten cylinder lock screw (clockwise) through front of mortise lock. c.
Page 20
IN100 Series Exit Device 8900 & PE8900 Lock Installation for Mortise Exit Device (Continued) Install rail assembly. (Figure 21) a. Retrieve harness from end of rail. Harness has limited travel and can be damaged. b. Attach harness to female connector on chassis.
Page 21
IN100 Series Exit Device PE8600 Installation Instructions for PE8600 Concealed Vertical Rod (CVR) Exit Device (EA Option) 1. Prepare door Inside a. Verify hand and bevel of door. (Fig. 1) NOTE: Stand on outside of locked door when determining door hand. b.
IN100 Series Exit Device PE8600 Installation Instructions for PE8600 Concealed Vertical Rod (CVR) Exit Device (EA Option) Install door position switch* (DPS). NOTE: Wood doors have 3/8" raceway to controller cutout and metal doors have 3/4" raceway to DPS Jumper controller cutout.
Page 23
IN100 Series Exit Device PE8600 Installation Instructions for PE8600 Concealed Vertical Rod (CVR) Exit Device (EA Option) 3. Install Inner Case Assembly A. Wood Door (WD) 1. Install the inner case assembly with (2) #12 x 1” Phillips flathead screw (Fig. 5A). B.
Page 24
IN100 Series Exit Device PE8600 Installation Instructions for PE8600 Concealed Vertical Rod (CVR) Exit Device (EA Option) 4. Mount exit device chassis. a. Mount exit chassis loosely, using only the top left mounting screw. Screw should support the weight of the chassis but allow it to move freely while routing the wiring Inside of and mounting exit trim.
Page 25
IN100 Series Exit Device PE8600 Installation Instructions for PE8600 Concealed Vertical Rod (CVR) Exit Device (EA Option) Secure exit chassis. (Fig. 10) To comply with UL certifications and for security: a. Fasten exit chassis to door using three (3) remaining #10 wood screws (for wood door) or four (4) #10-24 machine screws (for metal door).
IN100 Series Exit Device PE8700 Installation Instructions for PE8700 Surface Vertical Rod (SVR) Exit Device (EA Option) 1. Prepare door a. Verify hand and bevel of door. (Fig. 1) Inside NOTE: Stand on outside of locked door when determining door hand. b.
Page 27
IN100 Series Exit Device PE8700 Installation Instructions for PE8700 Surface Vertical Rod (SVR) Exit Device (EA Option) Install door position switch* (DPS). Insert connector end of DPS through raceway on latch edge of door. (Fig. 3) NOTE: For metal doors, use DPS collar. b.
Page 28
IN100 Series Exit Device PE8700 Installation Instructions for PE8700 Surface Vertical Rod (SVR) Exit Device (EA Option) 3. Install Outside Trim and Exit Chassis Align exit trim and gasket (if required) with through-holes: a. For exterior application, use trim gasket to seal between trim Outside of Door escutcheon and outside door surface (Fig.
Page 29
IN100 Series Exit Device PE8700 Installation Instructions for PE8700 Surface Vertical Rod (SVR) Exit Device (EA Option) Install rail assembly. (Fig. 8) a. Retrieve harness from end of rail. Harness has limited travel and can be damaged. b. Attach harness to female connector on chassis. c.
IN100 Series Exit Device IN100 Installation Install outside reader. a. Orient reader so LED lens is at top. (Figure 22) b. Feed cable/connector through door from outside to inside. c. Install reader to outside of door by aligning mounting posts with door preparation holes. Hold reader flush against door while ensuring proper alignment.
Page 31
IN100 Series Exit Device IN100 Installation (Continued) g. Secure the following connectors to their respective terminals (Figure 25): *Optional 12-24VDC Power CAUTION: Do not touch or allow debris to enter connector contacts Remote Power Harness Wire Terminations • Secure 4-pin DPS connector 2-pin Black PS (-) Return...
Page 32
IN100 Series Exit Device IN100 Installation (Continued) Install inside component assembly (controller). a. (Making sure path is clear) insert bottom tab of controller into slot on mounting plate. Controller (Figure 28) b. Ensure proper alignment of board-to-board connectors while pivoting controller toward door until two tabs on top snap securely into place on mounting plate.
IN100 Series Exit Device IN100 Installation (Continued) Install inside cover. (Figure 31) a. Assemble cover by hooking top edge on inside mounting plate. b. Carefully press bottom of cover toward door without pinching or Inside damaging wires. Cover c. Secure cover utilizing security hex key. NOTE: Use of power tools on this step is strongly discouraged.
IN100 Series Exit Device Communications Hub Indications Communications hub has a single LED. It supports an optical scheme of red, green and yellow. Indication scheme is described by figures below: Communications Hub NORMAL OPERATION LED indication 2 sec. Online Green Aperio lock Green + one...
IN100 Series Exit Device Lock LED Indications Lock NORMAL OPERATION LED indication EAC response time Enter PIN Card + PIN access (configurable) Card access (configurable) One yellow flash (.25 second) Access granted, EAC offline or online One green flash (1 sec.) Access denied, EAC online One red flash (1 sec.) Force closed in remote open/office mode...
IN100 Series Exit Device Lock Self-Test LED Indications After replacing batteries, a Power on Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as described by figures below: Battery Not Fully Charged Error in lock is an indication -10 quick (125ms) red blinks, that either new batteries are not at right voltage or a backward battery has been installed;...
IN100 Series Exit Device Lock Busy LED Indications Lock BUSY indicates lock is processing a card (such as a key configuration card for online SE processor or offline void list card with many entries). Card should be kept in close proximity to reader until end of process. Lock BUSY indi- cation does not cancel or overwrite any other indications.
Need help?
Do you have a question about the SARGENT IN100 Series and is the answer not in the manual?
Questions and answers