Assa Abloy SARGENT Profile Series Installation Instructions Manual
Wifi cylindrical lock
Hide thumbs
Also See for SARGENT Profile Series:
- Installation instructions manual (24 pages) ,
- Installation instructions manual (20 pages) ,
- Installation instructions manual (28 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Assa Abloy SARGENT Profile Series
Summary of Contents for Assa Abloy SARGENT Profile Series
-
Page 1: Installation Instructions
Profile WiFi Cylindrical Lock Installation Instructions A7785E 02/11 Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. -
Page 2: Table Of Contents
Table of Contents Warning ..................2 General Description ..............3 Hardware Specifications ............3 Electronic Specifications ............3 Installation Wiring Overview ...........3 Lock Wiring ................4 Parts Breakdown ..............5 Installation Instructions ............7 Operational Check ..............14 Warning Warning: Changes or modifications to this unit not expressly approved by ASSA ABLOY Inc. -
Page 3: General Description
General Description The SARGENT Profile Series v.S2 cylindrical lock is is available with either an HID® 125 kHz prox or 13.56 MHz iCLASS® technology reader. Either can be used in applications requiring wireless access control. The v.S2 is a self-contained microprocessor-controlled access control product with non-volatile memory. -
Page 4: Lock Wiring
Profile Series v.s2 WiFi Cylindrical Lock Lock Wiring Controller Board Connectors (Inside Escutcheon) COM (VIOLET) NC (PINK) Power From Outside From Escutcheon Lock A7785E... -
Page 5: Parts Breakdown
Profile Series v.s2 WiFi Cylindrical Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS A7785E... - Page 6 Profile Series v.s2 WiFi Cylindrical Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, Continued ITEM PART NO. DESCRIPTION REQ’D Outside Lever Reference Cylindrical/10 Line Catalog For Available Levers Inside Lever Reference Cylindrical/10 Line Catalog For Available Levers 10-3016 Outside Escutcheon Assembly 10-3015 Inside Escutcheon Assembly...
-
Page 7: Installation Instructions
Profile Series v.s2 WiFi Cylindrical Lock Installation Instructions Step #1 – Door Preparation A. Verify Hand and Bevel of Door Stand on outside/locked side of door when determining the door hand LHRB RHRB Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right... - Page 8 Profile Series v.s2 WiFi Cylindrical Lock Centerline of Latch Front and Strike Step #2 – Install Strike Install strike in the door frame (Fig.2A). (2) #8-32 x 3/4" Latch Screws Outside of Door Fig. 2A Step #3 - Install Latchbolt 1.
- Page 9 Profile Series v.s2 WiFi Cylindrical Lock Step #5 – Lock Adjustment Through-bolt Hole A. Lock Preset: • Lock body holes: 12 and 6 o’clock (Fig. 5A). Outside of Door • Door thickness: 1-3/4” thick. Refer to adjustments below for other door conditions (Fig. 5B Detail). B.
- Page 10 Profile Series v.s2 WiFi Cylindrical Lock Outside of Door Step #7 - Install Lock 1. Feed wires into the lock body hole from outside of door (Fig.7A). 2. Slide lock body into cross-bore hole from outside (locked side) of the door (Fig.7B). 3.
- Page 11 Profile Series v.s2 WiFi Cylindrical Lock Step #9 – Install Door Position Switch (DPS) 1. Prep door according to proper template: Wood: A7980 Metal: 4632. 2. Insert DPS into the raceway on the latch edge of the door. 3. To insert DPS, push wires through raceway toward lock prep. Note: Only use collar when installing in a metal door.
- Page 12 Profile Series v.s2 WiFi Cylindrical Lock Inside of Door Step #11 – Escutcheon Wire Connections Images are shown without gasket. If gasket is necessary, refer to Step #10. Before the controller is attached Reader to the door: Ribbon Cable 1. Attach the reader assembly ribbon cable into the back of Antenna (iCLASS)
- Page 13 Profile Series v.s2 WiFi Cylindrical Lock Step #13 – Install Inside Escutcheon 1. Gently fold the excess ribbon connector and ground wire into the top hole and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig.
-
Page 14: Operational Check
The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.