Danfoss VLT HVAC Basic Drive FC 101 Programming Manual page 18

Programming
Set-up Wizard for Closed-loop Applications
2 2
Illustration 2.5 Set-up Wizard for Closed-loop Applications
16
®
VLT
PM motor
1-24 Motor Current
A
3.8
1-25 Motor Nominal Speed
3000 RPM
1-26 Motor Cont. Rated Torque
5.4 Nm
1-30 Stator Resistance
0.65 Ohms
1-39 Motor Poles
8
1-40 Back EMF at 1000 RPM
57 V
1-37 d-axis inductance(Lq)
5 mH
Motor type = IPM
Motor type = SPM
Motor type = PM motor
Current
6-22 T54 Low Current
04.66
A
6-24 T54 low Feedback
0016 Hz
6-23 T54 high Current
13.30
A
6-25 T54 high Feedback
0050
Hz
Danfoss A/S © 04/2018 All rights reserved.
HVAC Basic Drive FC 101
... the Wizard starts
0-03 Regional Settings
[0] Power kW/50 Hz
0-06 Grid Type
[0] 200-240V/50Hz/Delta
1-00 Configuration Mode
[3] Closed Loop
1-10 Motor Type
Asynchronous motor
[0] Asynchronous
1-38 q-axis inductance(Lq)
5 mH
(1-70) Start Mode
[0] Rotor Detection
1-46 Position Detection Gain
100 %
30-22 Locked Rotor Detection
[0] Off
30-23 Locked Rotor Detection Time[s]
0.10 s
4-19 Max Ouput Frequency
0065 Hz
1-42 Motor Cable Length
50
m
4-12 Motor speed low limit
0016 Hz
4-13 Motor speed high limit
0050 Hz
3-41 Ramp 1 ramp-up time
0010 s
3-42 Ramp1 ramp-down time
Motor type = Asynchronous
0010 s
1-73 Flying Start
[0]
20-00 Feedback 1 source
This dialog is forced to be set to
[1] Analog input 54
[1] Analog input 54
3-16 Reference Source 2
[0] No Operation
3-02 Min Reference
0.00
3-03 Max Reference
50.00
3-10 Preset reference [0]
0.00 %
6-29 Terminal 54 Mode
[1] Voltage
6-26 T54 Filter time const.
6-20 T54 low Voltage
0.01 s
20-81 PI Normal/Inverse Control
6-24 T54 low Feedback
[0] Normal
20-83 PI Normal/Inverse Control
0050 Hz
6-21 T54 high Voltage
20-93 PI Proportional Gain
00.50
6-25 T54 high Feedback
20-94 PI integral time
0020.00
s
1-29 Automatic Motor Adaption
[0] Off
... the Wizard starts
1-20 Motor Power
1.10 kW
1-22 Motor Voltage
400 V
1-23 Motor Frequency
50 Hz
1-24 Motor Current
04.66 A
1-25 Motor nominal speed
1420 RPM
1-44 d-axis Inductance Sat. (LdSat)
5 mH
(1-45) q-axis Inductance Sat. (LqSat)
5
mH
(1-48) Current at Min Inductance for d-axis
100 %
1-49 Current at Min Inductance for q-axis
100
%
No
Voltage
0050 V
Hz
0016
0220 V
0050 Hz
MG18B502