Veichi AC300 Series Technical Manual page 88

AC300 Series Vector Control Inverter Manual
F12.27 PLC 12th step running 0.0～6500.0(s/m/h)
F12.28 PLC 13th step running 0.0～6500.0(s/m/h)
PLC 14th step running
F12.29 0.0～6500.0(s/m/h)
F12.30 PLC 15th step running 0.0～6500.0(s/m/h)
F12.31
F12.32
F12.33
LED"0" digit: current step run
F12.34
direction
0: FWD
F12.35
1: REV
F12.36
LED"00" digit: ACC/DEC time in
F12.37
PLC 1st-15th step
this step
F12.38 direction and ADD/DEC
0: ACC/DEC time 1
time
F12.39
1: ACC/DEC time 2
F12.40
2: ACC/DEC time 3
F12.41
3: ACC/DEC time 4
F12.42 LED"000" digit: Reserved
LED"0000" digit: Reserved
F12.43
F12.44
F12.45
F12.46
Reserved
-
F12.49 Swing frequency control 0: invalid
Swing frequency 0: Relative to central frequency
F12.50
amplitude 1: Relative to max frequency
F12.51 Reserved 0.0～100.0%
F12.52 Swing frequency
Jump frequency
F12.53 0.0～50.0%
lit d
Swing frequency rising
F12.54 0.00～650.00s
F12.55 Swing frequency falling 0.00～650.00s
Communication Control Function Parameter Group
NO. Function description Range of setting and definition
LED "0" digit: Modbus
main-slave selection
F13.0 Main-slave machine
0: Slave machine
0 selection
1: Main machine
F13.0 485 communication 1～247
LED"0" digit:485 communication
0:1200 bps
F13.0 Communication baud rate 2:4800 bps
2 selection 4:19200 bps
LED "00" /"000"/"0000"digit:
reserved
Function Parameter Table
10.0 ● 0xC1B
10.0 ● 0xC1C
10.0 ● 0xC1D
10.0 ● 0xC1E
0000 ● 0xC1F
0000 ● 0xC20
0000 ● 0xC21
0000 ● 0xC22
0000 ● 0xC23
0000 ● 0xC24
0000 ● 0xC25
0000 ● 0xC26
0000 ● 0xC27
0000 ● 0xC28
0000 ● 0xC29
0000 ● 0xC2A
0000 ● 0xC2B
0000 ● 0xC2C
0000 ● 0xC2D
1: valid 0 ● 0xC31
0 ● 0xC32
10.0% ● 0xC34
10.0% ●
5.00s ● 0xC36
5.00s ● 0xC37
Factory
Feature Address
default
0000 0xD00
〇
1 0xD01
〇
1:2400 bps
3:9600 bps
0003 0xD02
〇
5:38400 bps
172
AC300 Series Vector Control Inverter Manual
0:
F13.0
(N,8,1)format
Modbus data format
3
1: (E,8,1)
f
F13.0 Communication ratio 0.00～5.00
F13.0 Modbus communication
0～500ms
5 answer delay
F13.0 Modbus communication
0.1～100.0s
6 overtime fault time
0: No checked overtime fault
Modbus communication
F13.0 1: alarm and stop freely
fault action mode
7 2: Alarm and continue running
selection
3: Forced stop
F13.0 Modbus Responds 0:Write operation with response
8 dispose 1: Write operation without response
LED"0"digit: the first group
transmitting frame selection
0: Invalid
1: Main machine run command
2: Main machine given frequency
3: Main machine output frequency
4: Main machine upper limit
frequency
5: Main machine given torque
6: Main machine output torque
F13.0 Main machine sending
7/8: Reserved
9 selection
9: Main machine given PID
A: Main machine feedback PID
LED"00"digit: the second group
transmitting frame selection
LED"000"digit:
the third group transmitting
frame selection
LED"0000"digit: the fourth group
transmitting frame selection
Same as above
F13.1 RS485 Communication 0: Modbus communication
0 port configuration 1: serial port communication
Terminal of Input and Output Function Selection
X Function Specification X Function Specification
16-1
0 No function Multispeed terminal 1-4
1 FWD 20 PID control cancel
2 REV 21 PID control pause
3 3-line running(Xi) 22 PID trait switch
4 FWD JOG 23 PID gain switch
Function Parameter Table
3: (N,8,2) format
4: (E,8,2) format
0 〇 0xD03
5: (O,8,2)
f
1.00 ● 0xD04
0ms ● 0xD05
1.0s ● 0xD06
0 ● 0xD07
0 ● 0xD08
0031 ● 0xD09
0 ● 0xD0A
X Function
41 Timer clear terminal
42 Counter input
43 Counter clear
DC braking
44
45 Pre excitation
173