Veichi AC300 Series Technical Manual page 87

AC300 Series Vector Control Inverter Manual
LED"0" digit: Feedback feature
selection
0: Positive feature
feature
F11.07 PID control selection LED"00"/"000" digit: Reserved
LED"0000" digit: Differential
adjustment properties
0: Differential bias
1: Differential of feedback
F11.08 PID preset output 0.0～100.0%
PID preset output
F11.09 0.0～6500.0s
running time
PID control deviation
F11.10 0.0～100.0%
F11.11 Proportional gain P1 0.000～8.000
F11.12 Integral time I1 0.0～600.0s
F11.13 Differential time D1 0.000～6.000s
F11.14 Proportional gain P2 0.000～8.000
F11.15 Integral time I2 0.0～600.0s
F11.16 Differential gain D2 0.000～6.000s
0: No switch
PID Parameter
F11.17 1: Use DI terminal to switch
switching condition
2: Switch according to deviation
Low value of
F11.18 0.0～100.0%
switching deviation
High value of
F11.19 0.0～100.0%
switching deviation
F11.20 Reserved
F11.21 Differential limit 0.0～100.0%
F11.22 PID output upper limit 0.0～100.0%
F11.23 PID output lower limit -100.0～F11.19
F11.24 PID output filter time 0.000～6.000s
Feedback wire break
F11.25 0.0～120.0s
detection time
0: Go on PID operation without alarm
1: Stop and alarm malfunction
Feedback wire break 2: continue to PID operation and
F11.26
action selection output alarm signal
3: Run at the current frequency and
output alarm signal
Wire break alarm
F11.27 0.0～100.0%
F11.28 Wire break alarm 0.0～100.0%
Close-loop suspend
F11.29 0.0～100.0%
detection threshold
Close-loop suspend
F11.30 0.0～600.0s
detection time
Function Parameter Table
1:Negative
0100 ● 0xB07
100.0% ● 0xB08
0.0s ● 0xB09
0.0% ● 0xB0A
0.100 ● 0xB0B
1.0s ● 0xB0C
0.000s ● 0xB0D
0.100 ● 0xB0E
1.0s ● 0xB0F
0.000s ● 0xB10
0 ● 0xB11
20.0% ● 0xB12
80.0% ● 0xB13
0xB14
5.0% ● 0xB15
100.0% ● 0xB16
0.0% ● 0xB17
0.000s ● 0xB18
1.0s ● 0xB19
0 ● 0xB1A
100.0% ● 0xB1B
0.0% ● 0xB1C
0.0% ● 0xB1D
1.0s ● 0xB1E
170
AC300 Series Vector Control Inverter Manual
Multi-Speed and PLC Function Parameter Group
NO. Function description Range of setting and definition
F12.00 PLC Speed 1 0.00～Max frequency
F12.01 PLC Speed 2 0.00～Max frequency
F12.02 PLC Speed 3 0.00～Max frequency
F12.03 PLC Speed 4 0.00～Max frequency
F12.04 PLC Speed 5 0.00～Max frequency
F12.05 PLC Speed 6 0.00～Max frequency
F12.06 PLC Speed 7 0.00～Max frequency
F12.23 PLC Speed 8 0.00～Max frequency
F12.08 PLC Speed 9 0.00～Max frequency
F12.09 PLC Speed 10 0.00～Max frequency
F12.10 PLC Speed 11 0.00～Max frequency
F12.11 PLC Speed 12 0.00～Max frequency
F12.12 PLC Speed 13 0.00～Max frequency
F12.13 PLC Speed 14 0.00～Max frequency
F12.14 PLC Speed 15 0.00～Max frequency
LED"0" digit: cycle mode
0: Stop after single cycle
1: Continuous cycles
2: Keep final value after single cycle
LED"00" digit: Time unit
0: second
2:hour
PLC Running mode
F12.15 LED"000" digit: Power down
selection
memory
0: Not save
LED"0000" digit: Start mode
0: Restart from the 1st stage
1: Restart from the stop stage
2: Continue running from the time
when stop
PLC 1st step running
F12.16 0.0～6500.0(s/m/h)
F12.17 PLC 2nd step running 0.0～6500.0(s/m/h)
F12.18 PLC 3rd step running 0.0～6500.0(s/m/h)
F12.19 PLC 4thstep running time 0.0～6500.0(s/m/h)
F12.20 PLC 5th step running 0.0～6500.0(s/m/h)
F12.21 PLC 6th step running 0.0～6500.0(s/m/h)
PLC 7th step running
F12.22 0.0～6500.0(s/m/h)
F12.23 PLC 8th step running 0.0～6500.0(s/m/h)
PLC 9th step running
F12.24 0.0～6500.0(s/m/h)
F12.25 PLC 10th step running 0.0～6500.0(s/m/h)
F12.26 PLC 11th step running 0.0～6500.0(s/m/h)
Function Parameter Table
Factory
Feature Address
default
10.00Hz ● 0xC00
20.00Hz ● 0xC01
30.00Hz ● 0xC02
40.00Hz ● 0xC03
50.00Hz ● 0xC04
40.00Hz ● 0xC05
30.00Hz ● 0xC06
20.00Hz ● 0xC07
10.00Hz ● 0xC08
20.00Hz ● 0xC09
30.00Hz ● 0xC0A
40.00Hz ● 0xC0B
50.00Hz ● 0xC0C
40.00Hz ● 0xC0D
30.00Hz ● 0xC0E
1: minute
0000 ● 0xC0F
1: save
10.0 ● 0xC10
10.0 ● 0xC11
10.0 ● 0xC12
10.0 ● 0xC13
10.0 ● 0xC14
10.0 ● 0xC15
10.0 ● 0xC16
10.0 ● 0xC17
10.0 ● 0xC18
10.0 ● 0xC19
10.0 ● 0xC1A
171