Veichi AC300 Series Technical Manual page 77

AC300 Series Vector Control Inverter Manual
0: Channel A
1: Channel B
Frequency given 2: Channel A+Channel B
F00.06
source selection 3: Channel A-Channel B
4: Max. value of Channel A and Channel B
5: Min. value of Channel A and Channel B
LED"0"digit: keyboard command
instruction binding
LED"00"digit: terminal command
instruction binding
LED"000"digit: communication command
instruction binding
LED"0000"digit: optional card command
instruction binding
0 : no binding
1 : keyboard number given frequency
Running Command
F00.07 2 : Reserved
Binding
3 : Voltage/Current analog AI1 given
4 : Voltage/Current analog AI2 given
5 : Reserved
6 : Terminal pulse PUL given
7: RS485 communication given
8 : Terminal UP/DW control
9 : PID control given
A: Program control (PLC) given
B: Optional card
C: Multi-steps speed given
Keyboard digital
F00.08 0～upper limit
setting frequency
F00.09 Max frequency upper limit～600.00Hz
0: Upper limit frequency digital given
1: Reserved
2: Voltage/Current analog AI1 give
Upper limit
3: Voltage/Current analog AI2 given
F00.10 frequency source
4: Reserved
selection
5: Terminal pulse PUL given
6: RS485 communication given
7: Optional card
Upper frequency
F00.11 Lower limit frequency～max frequency
limit digital setting
Lower limit
F00.12 0.00～upper limit frequency
Lower limit
0: Stop output, enter into pause running state
F00.13 frequency running
1: Run at lower limit frequency
mode
F00.14 ACC time 1 0.01～650.00s
F00.15 DEC time 1 0.01～650.00s
LED"0"digit: running direction takes the
Rotary direction
F00.16 opposite
selection
0: Direction unchanged
Function Parameter Table
0 ● 0x006
0000 ● 0x007
50.00Hz ● 0x008
50.00Hz 0x009
〇
0 ● 0x00A
50.00Hz ● 0x00B
0.00Hz ● 0x00C
1 0x00D
〇
Model 0x00E
※
Model 0x00F
※
0000 0x010
〇
150
AC300 Series Vector Control Inverter Manual
1: Direction takes the opposite
LED"00"digit: running direction
prohibited
0:Forward and reverse commands are
allowed
1: Only FWD command allowed
2: Only REV command allowed
LED"000"digit: frequency control
direction selection
0: Invalid 1: Valid
LED"0000"digit: reserved
F00.17 G/P Model Setting 0: G Type
F00.18 Reserved
0: No action
1: Restore factory default (not restoring motor
Parameter parameters)
F00.19
initialization 2: Restore factory default (restoring motor
parameters)
3: Clear malfunction records
Operation Control Parameters Group
NO. Function description Range of settings and definition
0: Start by start-up frequency
1: DC Braking at first then start by
F01.00 Start-up running mode start-up frequency
2: Speed tracking, and judge the
direction then start
F01.01 Start pre-excitation time 0.00～60.00s
F01.02 Start-up frequency 0.00～60.00Hz
F01.03 Start-up frequency holding 0.0～50.0s
F01.04 Braking current before 0.0～150.0%
F01.05 Braking time before start 0.0～60.0s
F01.06 Speed tracking time 0.00～60.00s
F01.07 Speed tracking delay 0.00～60.00s
F01.08 Reserved
F01.09 Reserved
F01.10 Stop mode 0:DEC stop
DC braking initial
F01.11 0.00～50.00Hz
frequency when stop
F01.12 DC braking current when 0.0～150.0%
F01.13 Reserved
F01.14 DC braking hold time 0.0～60.0s
F01.15 Stop detection frequency 0.00～50.00Hz
Function Parameter Table
1: P Type 0 ● 0x011
0x012
0 0x013
〇
Factory
Feature Address
setting
0 0x100
〇
0.00s 0x101
〇
0.50Hz 〇 0x102
0.0s 0x103
〇
60.0% 0x104
〇
0.0s 0x105
〇
0.50s 0x106
〇
1.00s 0x107
〇
1:Free stop 0 ● 0x10A
1.00Hz 0x10B
〇
60.0% 0x10C
0x10D
0.0s 0x10E
〇
0.50Hz ● 0x10F
151