Veichi AC300 Series Technical Manual page 86

AC300 Series Vector Control Inverter Manual
LED"0" digit: Detection
selection(protection 1)
0: Not detection
1: Detected load is too large
2: Detected load is too large only at
constant speed
3: Detected underloaded
4: Detected underloaded only at
constant speed
LED"00" digit: Alarm selection
0: alarm and continue operation
Load pre alarm
F10.17
1: Fault protection and free stop
detection setting
LED"000" digit: Detection
selection
(protection 2)
0: Not detection
1: Detected load is too large
2: Detected load is too large only at
constant speed
3: Detected underloaded
4: Detected underloaded only at
constant speed
Pre alarm detection
F10.18 0.0～200.0%
level 1 for load
Load pre alarm
F10.19 0.0～60.0s
detection time 1
Pre alarm detection
F10.20 .0～200.0%
level 2 for load
Load pre alarm
F10.21 0.0～60.0s
detection time 2
F10.22 Reserved
LED "0" digit: Detection selection
0: Not detected
1: Detected only at constant speed
Protection action of 2: Detecting
F10.23
speed bias excess LED "00" digit: Alarm selection
0: Free stop and report fault
1: Alarm and continue operation
LED "000"/"0000" digit: Reserved
Detection threshold
F10.24 0.0～60.0%
when speed bias
Detection time when
F10.25 0.0～60.0s
speed bias excess
Function Parameter Table
0000 0xA11
〇
130.0% 〇 0xA12
5.0s 0xA13
〇
30.0% 0xA14
〇
5.0s 〇 0xA15
0xA16
0000 0xA17
〇
10.0% 〇 0xA18
2.0s 0xA19
〇
168
AC300 Series Vector Control Inverter Manual
LED "0" digit: Detection selection
0: Not detected
1: Detected at constant speed
2: Detecting
F10.26 Stall protection action LED "00" digit: Alarm selection
0: Free stop and report fault
1: Alarm and continue operation
LED "000" digit: Reserved
LED "0000" digit: Reserved
Stall detection
F10.27 0.0～150.0%
F10.28 Stall detection time 0.000～2.000s
Motor overshot
F10.29 0～200°C
Protection threshold
Motor overshot Pre
F10.30 0～200°C
alarm threshold
F10.31-F
Reserved
10.37
Malfunction
F10.38 0～5
self-recovery times
Malfunction
F10.39 0.1～100.0s
self-recovery interval
PID Process Control Parameter Group
NO. Function description Range of settings and definition
0: Keypad digit PID
given
PID Controller given 1: Reserved
F11.00
signal source 2: AI1
3: AI2
4: Reserved
Keyboard digit PID
F11.01 0.00～100.0%
given / feedback
F11.02 PID given changing 0.00～60.00s
0: Keypad digital
PID feedback
PID controller 1: Reserved
F11.03 feedback signal 2: AI1
source 3:AI2
F11.04 Feedback signal filter 0.000～6.000s
F11.05 Feedback signal gain 0.00～10.00
F11.06 Given and feedback 0～100.0
Function Parameter Table
0000 0xA1A
〇
110.0% 0xA1B
〇
0.010s 0xA1C
〇
0xA1D
〇
0xA1E
〇
0 0xA26
〇
1.0s 0xA27
〇
Factory
Feature Address
default
5: PUL
6: RS485
7: Option
0 ● 0xB00
card
8:Terminal
selection
50.0% ● 0xB01
1.00s ● 0xB02
4: Reserved
5: PUL
6: RS485
7: Option 2 ● 0xB03
card
8:Terminal
selection
0.010s ● 0xB04
1.00 ● 0xB05
100.0 ● 0xB06
169