Veichi AC300 Series Technical Manual page 79

AC300 Series Vector Control Inverter Manual
channel switch to terminal
0: Common X terminal
F02.25 Counter input 1: High speed input terminal PUL
2: PG card counting
F02.26 Count input frequency 0～6000
0: X5(max～5 KHz)
F02.27 PUL signal source
1: Extend interface X10
F02.28 PUL input min frequency 0.00～50.00 KHz
PUL min frequency
F02.29 0.00～100.00%
corresponding setting
F02.30 PUL input max frequency 0.00～50.00 KHz
PUL max frequency
F02.31 0.00～100.00%
corresponding setting
F02.32 PUL filter time 0.000～9.000s
F02.33 PUL cut-off frequency 0.000～1.000 KHz
0: Off electricity storage
UP/DW terminal control
1: Off electricity does not storage
F02.34
mode
2: Valid in running, clear zero at
t
ACC/DEC speed of
F02.35 UP/DW terminal 0.01～50.00Hz/s
frequency control
F02.36 Reserved
F02.37 Timer time unit 0:Second
F02.38 Timer setting value 0～65000
F02.39 Counter max value 0～65000
F02.40 Counter setting value 0～65000
F02.41 Reserved
0: Positive 1: Negative
LED "0" digit: Terminal Y
LED "00" digit: Relay output 1
Output terminal polarity
F02.42 LED "000" digit: Extended Y1
selection
terminal
LED "0000" digit: Extended
Relay output 2
F02.43 Output terminal Y1 Refer to function table 4.2
F02.44 Relay output Refer to function table 4.2
F02.45 Extend terminal Y1 Refer to function table 4.2
Extend relay output 2 Refer to function table 4.2
F02.46
F02.47 Y output delay time 0.000～6.000s
F02.48 Extend Y output delay 0.000～6.000s
F02.49 Relay 1 output delay time 0.000～6.000s
F02.50 Extend relay 2 output 0.000～6.000s
Output frequency level
F02.51 0.00～Max. frequency
F02.52 FDT1 lag 0.00～Max. frequency
F02.53 Output frequency level 0.00～Max. frequency
Function Parameter Table
0 ● 0x219
0 ● 0x21A
0 〇 0x21B
0.00kH
● 0x21C
0.00% ● 0x21D
50.00k ● 0x21E
100.00
● 0x21F
%
0.100s ● 0x220
0.010k ● 0x221
0 0x222
〇
0.50Hz
● 0x223
/s
0x224
1:Minute 2:Hour 0 ● 0x225
0 ● 0x226
1000 ● 0x227
500 ● 0x228
0x229
0000 ● 0x22A
1 ● 0x22B
4 ● 0x22C
0x22D
0x22E
0.010s ● 0x22F
0.010s ● 0x230
0.010s ● 0x231
0.010s ● 0x232
30.00H
● 0x233
1.00Hz ● 0x234
50.00H ● 0x235
154
AC300 Series Vector Control Inverter Manual
F02.54 FDT2 lag 0.00～Max. frequency
Given frequency arriving
F02.55 0.00～50.00Hz
checkout range
Virtual vX1 terminal
F02.60 Refer to function table 4.2
function selection
Virtual vX2 terminal
F02.61 Refer to function table 4.2
function selection
Virtual vX3 terminal
F02.62 Refer to function table 4.2
function selection
Virtual vX4 terminal
F02.63 Refer to function table 4.2
function selection
0: internal connection with virtual
vYn
1: Connect with physical terminal
vX terminal valid state
F02.64 Xn
source
2: function code setting valid or not
LED "0" digit: virtual vX1
LED "00" digit: virtual vX2
0: invalid 1: valid
Virtual vX terminal LED "0" digit: virtual vX1
F02.65 function code setting valid LED "00" digit: virtual vX2
state LED "000" digit: virtual vX3
LED "0000" digit: virtual vX4
Virtual vY1 terminal
F02.66 Refer to function table 4.2
function selection
Virtual vY2 terminal
F02.67 Refer to function table 4.2
function selection
Virtual vY3 terminal
F02.68 Refer to function table 4.2
function selection
Virtual vY4 terminal
F02.69 Refer to function table 4.2
function selection
F02.70 vY1 output delay 0.000～6.000s
F02.71 vY2 output delay 0.000～6.000s
F02.72 vY3 output delay 0.000～6.000s
Virtual vY2 output
F02.73 0.000～6.000s
Analog Terminal Parameters
NO. Function description Range of settings and definition
F03.00 AI1 Lower limit 0.00～10.00V
AI1 Lower limit
F03.01 -100.00～100.00%
corresponding setting
F03.02 AI1 upper limit 0.00～10.00V
Function Parameter Table
1.00Hz ● 0x236
2.00Hz ● 0x237
0 ● 0x238
0 ● 0x239
0 ● 0x23A
0 ● 0x23B
0 ● 0x23C
0 ● 0x23D
0 ● 0x23E
0 ● 0x23F
0 ● 0x240
0 ● 0x241
0.010 ● 0x242
0.010 ● 0x243
0.010 ● 0x244
0.010 ● 0x245
Factory
Feature Address
setting
0.00V ● 0x300
0.00% ● 0x301
10.00V ● 0x302
155