Veichi AC300 Series Technical Manual page 83

AC300 Series Vector Control Inverter Manual
LED "0" digit: encoder mode
0: Common ABZ encoder
1: Resolver encoder
LED "00" digit: encoder direction
0: same direction
Speed feedback or 1: reverse direction
F05.30
encoder mode LED "000" digit: wire break
inspection
0: OFF 1: ON
LED"0000"digit:Z pulse correction
enabled
0: OFF 1: ON
F05.31 ABZ encoder lines 0-10000
wire break inspection
F05.32 0.100-60.000s
F05.33 Resolver encoder 2～128
Numerator of encoder
F05.34 1～32767
transmission ratio
Denominator of
F05.35 1～32767
encoder transmission
First-order filter of
F05.36 0.0～100.0ms
encoder speed
F05.37
Reserved
-
Motor VC Parameters
NO. Function description Range of settings and definition
ASR(speed loop)
F06.00 0.01～100.00
proportional gain 1
F06.01 ASR integral time 1 0.000～6.000s
F06.02 ASR filter time1 0.0～100.0ms
F06.03 ASR switch frequency 1 0.00～Max frequency
ASR (speed loop)
F06.04 0.01～100.00
proportional gain 2
ASR (speed loop) integral
F06.05 0.000～6.000s
time 2
F06.06 ASR filter time 2 0.0～100.0ms
F06.07 ASR switch frequency 2 0.00～Max frequency
F06.08 Electric motor torque limit 0.0～250.0%
Power generation torque
F06.09 0.0～250.0%
Current loop D-axis
F06.10 0.001～4.000
proportional gain
Current loop D-axis
F06.11 0.001～4.000
integral gain
Function Parameter Table
0000 0x51E
〇
1024 0x51F
〇
2.000s ● 0x520
2 0x521
〇
1 0x522
〇
1 0x523
〇
1.0ms ● 0x524
Factory
Feature Address
default
10.00 ● 0x600
0.200s ● 0x601
0.0ms ● 0x602
0.00Hz ● 0x603
10.00 ● 0x604
0.200s ● 0x605
0.0ms ● 0x606
5.00Hz ● 0x607
180.0% ● 0x608
180.0% ● 0x609
1.000 ● 0x60A
1.000 ● 0x60B
162
AC300 Series Vector Control Inverter Manual
Current loop Q-axis
F06.12 0.001～4.000
proportional gain
Current loop Q-axis
F06.13 0.001～4.000
integral gain
Vector control motor slip
F06.15 0.0～250.0%
compensation
F06.16 Vector control start torque 0.0～250.0%
F06.17 Reserved
Position compensation
F06.18 0:OFF 1:ON
control
F06.19 compensation gain 0.0～250.0%
F06.20 compensation limit 0.0～100.0%
F06.21 compensation effective 0.0～100.0%
Over excitation braking
F06.22 0.0～500.0%
Over excitation braking
F06.23 0.0～250.0%
amplitude limit
Vector control energy
F06.24 0:OFF 1:ON
saving function
Energy saving control
F06.25 0.0～80.0%
Energy saving control
F06.26 0.000～6.000s
low-pass filter
Motor constant power
F06.27 0.0～250.0%
area power limit
Motor weak magnetic
F06.28 0.0～250.0%
current upper limit
Motor weak magnetic
F06.29 0.0～200.0%
feed forward gain
F06.30 Motor weak magnetic 0.0～500.0%
F06.32 MTPA gain 0.0～500.0%
F06.33 MTPA filter time 0.0～100.0ms
F06.34 Reserved
F06.35 Low frequency pull in 0.0～100.0%
High frequency pull in
F06.36 0.0～100.0%
Frequency of current
F06.37 0.0～100.0%
pulled in
F06.38-F
Reserved
06.69
Torque Control Parameters
NO. Function description Range of settings and definition
0:Speed control
F07.00 Torque/Speed control
1:Torque control Torque/Speed
Function Parameter Table
1.000 ● 0x60C
1.000 ● 0x60D
100.0% ● 0x60F
0 0x612
〇
10.0% 0x613
〇
0.1% 0x614
〇
10.0% 0x615
〇
100.0% 0x616
〇
100.0% 0x617
〇
0 0x618
〇
50.0% ● 0x619
0.010s 0x61A
●
200.0% 0x61B
●
60.0% 0x61C
〇
10.0% 0x61D
●
10.0% 0x61E
●
●
10.0% 0x620
100.0% 0x621
●
1.0ms ● 0x621
0x622
10.0% 0x623
●
10.0% ● 0x624
10.0% 0x625
●
Factory
Feature Address
default
0 ● 0x700
163