Ikegami HLM-960WR Operation Manual page 27

Setting the ASPECT REFERENCE
Used to select automatic setting of a preset aspect
ratio or a fixed setting for all input channels,
when selecting input channels.
INPUT : displayed with the set aspect ratio
for each channel
COMMON : displayed with the same aspect
ratio for all channels
* When switching the ASPECT in the parallel re-
mote mode, set the ASPECT ratio to "COMMON".
Default setting is INPUT.
Setting the display size for PC signal with HDMI
Used to preset the image display size in receiving
a PC-format HDMI signal.
This is effective when a HDMI input mode has
been selected and the related signal is detected.
NORMAL : With the aspect ratio intact, im-
ages are enlarged or reduced to
the panel's maximum displaya-
ble size.
FULL : Images are fully displayed on-
screen (1920 x 1080) for all input
signals.
Default setting is NORMAL
Display pixels with respect to PC input signals in
each mode.
PC input signal Pixel size and aspect ratio
(pixels, aspect ratio)
NORMAL
VGA 1440 1080
(640 480 4:3)
(4:3)
SVGA 1440 1080
(800 600 4:3)
(4:3)
XGA 1440 1080
(1024 768 4:3)
(4:3)
WXGA 1800 1080
(1280 768 15:9)
(15:9)
SXGA 1350 1080
(1280 1024 5:4) (5:4)
UXGA 1440 1080
(1600 1200 4:3) (4:3)
WUXGA 1728 1080
(1920 1200 16:10)
(16:10)
Horizontal screen position adjustment
Adjust the horizontal screen position of the input
signal in the range of -100 to +100 ( In HLM-2460W
case : -30 to 30 ).
The setting values are memorized for each chan-
nel/each format.
For this setting, numerical values are not memo-
rized in the "POWER ON CONFIG" function.
Default setting is 0.
Vertical screen position adjustment
Adjust the vertical screen position of the input
signal in the range of -20 to +20.
The setting values are memorized for each chan-
nel/each format.
For this setting, numerical values are not memo-
rized in the "POWER ON CONFIG" function.
Default setting is 0.
Setting the APERTURE ON/OFF
Set the APERTURE ON/OFF.
This function can be assigned to a function switch
on the front panel.
Default setting is OFF.
Setting the APERTURE LEVEL
Set the APERTURE level in the range from 1 to 63.
Default setting is 16.
Setting the APERTURE frequency
Set the boost frequency of APERTURE.
LOW Boost from around 10MHz
MID1 Boost from around 15MHz
MID2 Boost from around 20MHz
HIGH Boost from around 25MHz
Default setting is HIGH.
Setting the COMB/TRAP of VBS
Set the filter for Y / C separation of a VBS signal.
FULL
COMB
1920 1080
TRAP
(16:9)
1920 1080
This function can be assigned to a function switch
(16:9)
on the front panel.
1920 1080
Default setting is COMB.
(16:9)
1920 1080
(16:9)
Setting the setup level of the NTSC signal
1920 1080
(16:9)
Sets the setup level when an NTSC signal is input.
1920 1080
If the black level of the signal has 7.5% setup, set
(16:9)
1920 1080
it to "7.5%".
(16:9)
Default setting is 0%.
- -
17
HLM-960WR / 1760WR / 2460W
COMB filter
TRAP filter