1. Manuals
  2. Brands
  3. Ikegami Manuals
  4. Monitor
  5. HTM-1005R
  6. Operation manual

Ikegami HTM-1005R Operation Manual

Hdtv/sdtv multi format color monitor
Hide thumbs Also See for HTM-1005R:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL
HTM-1005R/RA
HDTV/SDTV MULTI FORMAT
COLOR MONITOR
OPERATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Ikegami HTM-1005R

Summary of Contents for Ikegami HTM-1005R

  • Page 1 MODEL HTM-1005R/RA HDTV/SDTV MULTI FORMAT COLOR MONITOR OPERATION MANUAL...
  • Page 2 Caution (AC/DC input type) For the use of nickel-hydrogen batteries, a parallel connection of two or more batteries is possible. Battery makers, however, say that their warranty will not cover any products if they are used for “monitors or lighting equipment”, since the lifetime of batteries is shortened in such use environments due to the heat generated by the batteries themselves.
  • Page 3 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN SA 1965 SA 1966 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead inside a triangle is intended to warn the user that parts inside the product are dangerous and many cause electric hazards.
  • Page 4 IMPORTANT SAFETY INSTRUCTION 3) When connecting and disconnecting the 1. General power cable, be sure to hold the plug. 1) Read all instructions provided. 4) Do not allow anything to rest on the power 2) Save these instructions for future use. cord.
  • Page 5 3) Upon completion of any service or repairs to this monitor, ask the service technician to perform routine safety checks to determine that the television is in safe operating condition. 4) For repair service, contact Ikegami’s authorized sales representative or Ikegami service desk directly.

  • Page 6: Precautions For Operations

    In such cases, contact the Ikegami 4) If cabinet or screen is dirty, wipe with soft service desk.
  • Page 7 ON. In this case, immediately turn OFF the power second repeatedly and the high-tension section shuts down and contact the nearest Ikegami dealer. itself. If no image is displayed on screen but the POWER If the battery becomes dead, various adjustment data LED is blinking, therefore, immediately turn OFF the power.

  • Page 8: Table Of Contents

    (6) Description of MENU 4 functions ....34 (1) HTM-1005R ..........8 (7) Description of MENU 5 functions ....34 (2) HTM-1005R with DAM-1054/1058 ..... 9 (8) Description of MENU 6 functions ....34 3. Installation ............. 10 (9) Description of MENU 7 functions ....35 3.1 External connection ........

  • Page 9: General

    HTM-1005R/RA Multi-Format Color Monitor HTM-1005R/RA Multi-Format Color Monitor 1. General (3) Embedded audio output-compatible 1.1 General An optional embedded audio-compatible multi format SDI module This monitor is a 10-inch type HDTV/SDTV multi format color (DKM 1051AV/AVD), which is equipped with a demultiplexer monitor.
  • Page 10 (18) Lower power consumption (AC input-only type) extract from the rear without removing the cover, are easy to As compared with the conventional HTM-1005R, the HTM- maintain. 1005RA is designed as standard specifically for AC input and an...

  • Page 11: Specifications

    4. Aperture correction 2. Specifications +6 dB or more is variable at the following frequencies. 2.1 Common specifications a) HDTV 10 MHz ±2.5 MHz (1) General b) SDTV (for use of DE-1051) 5 MHz ±1 MHz 1. Power supply * No effect on the RGB input digital component or SDTV YPbPr a) AC-only type (standard) input AC, single-phase, 50/60 Hz...

  • Page 12: Function

    (5) Function (7) Applicable standards 1. Marker function 1. Safety standards a) Center marker Compliant with UL1950 The ON/OFF setting is made on the menu. 2. Electromagnetic interference b) Safe title FCC Class-A The following markers are displayed according to the aspect 3.

  • Page 13: Multi-Sdi Input Module (Option)

    4. Input impedance [Audio signal system specifications] High impedance bridge connection or 75 Ω termination 1. Embedded audio common specifications (The 75 Ω terminating plug is optional.) • Embedded audio input-compatible format 5. Return loss SMPTE272M: 480i/59.94 (4:2:2) 46 dB or more (10 MHz) 576i/50 (4:2:2) SMPTE299M: 1035i/60, 59.94 (2) MULTI-SDI input module (option)

  • Page 14: Embedded Audio Level Meter Display Module (Option)

    4. Speaker output section c) DK-10512 Embedded audio voices can also be output from the standard Compatible with both formats in a) and b) speaker. d) DEK-1052N (SDI input section) • Number of speakers: 1 channel (standard) SDI 4Fsc digital composite signal (NTSC) •...
  • Page 15 6. DEK-1052N 14. BR-1050L (It is impossible to mount this module in conjunction with Lithium ion battery adapter for BP-L90A DKM-1051* simultaneously.) (BP-L90A is diverted to this purpose in terms of capacity.) 4-input module designed to mount DK-1052N and DE-1051 in 15.

  • Page 16: Multi-Sdi Module

    (2)-3 MULTI-SDI module (DKM-1051AVD) option MULTI-SDI module (DKM-1051AVD) option MULTI SDI input • Input SDI signal here. • Acceptable input format 1. 480i / 59.94 (4 : 2 : 2) 5. 1080i / 50 (Option) 2. 576i / 50 (4 : 2 : 2) 6.

  • Page 17: Ntsc/Pal Decoder Module (De-1051) Option

    (4)-1 NTSC/PAL decoder module (DE-1051) option NTSC/PAL decoder module (DE-1051) option Analog composite input • Input NTSC/PAL signal. • Acceptable input format 1. 480i / 59.94 (NTSC) 2. 576i / 50 (PAL) • When loop through connections are not used, terminate with a terminating plug. •...

  • Page 18: Ypbpr/Rgb Input Module (Dch-1051) Option

    (5) YPbPr/RGB input module (DCH-1051) option YPbPr/RGB input module (DCH-1051) option YPbPr/RGB input • Input YPbPr signals or RGB signals. • Acceptable input format 1. 480i / 59.94 2. 576i / 50 3. 1035i / 59.94 (60) 4. 1080i / 59.94 (60) 5.

  • Page 19: Parallel Remote Connection

    3.2 Parallel remote connection (1) Pin function Functions of HTM-1050*/HTM-1005* parallel remote pins Pin No. Name Operation Remote connector wiring Connecting each remote terminal to Pin 1 allows On-control. CH-B on Connect to Pin 1 to select the B-channel at the time of CH-B on analog composite, SD-SDI, HD-SDI input.

  • Page 20: Power Supply

    3.3 Power supply (1) AC input type AC power input Insert the supplied AC cable here to supply AC power. AC plug retainer To prevent the AC plug from falling off, lock the AC plug with this hardware after insertion. AC IN (2) AC/DC input type Breaker (for DC power supply overcurrent protection)

  • Page 21: User Adjustment

    4. User adjustment 4.1 Names and functions of front panel parts MENU/ENT CHROMA BRIGHT CONT AUDIO DEGAUSS UTILITY ASPECT U–SCAN INPUT SET UP MONO SCREEN MARK POWER ANALOG HTM–1005R Front Panel 21 20 1. POWER switch 10. CHROMA manual control 18 to 21: INPUT changeover switches.
  • Page 22 7. ASPECT switch 16. MONO switch The switching between 4:3 and 16:9 is done. This switch performs the switching between COLOR and The settings (4:3/16:9) are memorized for each channel, so that MONO. the switching takes place automatically at the same time the In the MONO mode, the LED in the switch goes on.
  • Page 23 (1) 80% marker (7) Cross marker Effective screen area Effective screen area 100% area 80% area (2) 88% marker (8) 14:9 (100%) marker Effective screen area Effective screen area 100% area 14:9 (100%) area 88% area (3) 90% marker (9) 13:9 (100%) marker Effective screen area Effective screen area 100% area...

  • Page 24: Description Of Preset Data Manipulation

    switch 4.2 Description of preset data manipulation • Press this switch to move the cursor to a preset data item (1) Switch operation during presetting to be changed. When the PRE switch is pressed, the switches below function as follows. CENT SIZE MENU/ENT...
  • Page 25 1. PAGE 1 d. G.GAIN • Adjust the white balance (green component) in high light a. CONTRAST <CHANGE PRESET> b. BRIGHTNESS portions. *CONT* c. CHROMA For the adjustment procedures, refer to 4.4. (3). d. HUE e. APT CNT BRT CHR HUE APT e.

  • Page 26: Procedures For Registering Data In Memory Or Changing Data

    d. WIDTH 4.3 Procedures for registering data in • Adjust the width of the effective screen in each signal input memory or changing data FORMAT, each SCAN SIZE and each ASPECT. • For the adjustment procedures, refer to 4.4 (8). (1) Registering/changing PRESET data •...

  • Page 27: File Data Registration Or Change

    9. Data clear 4.4 Adjustment procedures Prior to the data registration shown in 8 above, pressing the (Introduction) ESC switch clears the changed data and returns to the previous • The following adjustments can be made with higher accuracy data that is not changed. in the darkest possible use environments for the monitor.

  • Page 28: White Balance Adjustment

    c. Adjustment steps 4. Initial adjustment of low light Produce the screen output of the R (red) signal only using 1. Input signal the SCREEN switch on the front panel. Adjust the Input a window signal (100%). R.BACKGROUND data to the extent that the red line in the 2.

  • Page 29: Color Balance Adjustment

    4. CONTRAST MANUAL setting b. Adjustment procedure (for NTSC composite signal) Place CONTRAST in the MANUAL mode and put the probe 1. Input signal of the color analyzer in the center of the window signal Input SMPTE color bar signal or similar NTSC 75% color displayed on the screen.

  • Page 30: Screen Center Adjustment

    c. Adjustment procedure 2 (for component signals) (5) Screen center adjustment 1. Input signal a. Screen center Apply a 100% color bar signal to the YPbPR signal input. To center the screen, make the following three types of adjustments. Different data can also be set individually in each Blue Blue Blue...

  • Page 31: Screen Distortion Adjustment

    c. Adjustment steps b. Caution The following adjustment steps are for a certain signal format. For SIDE PIN or TRAPEZOID adjustments, as in (6) above, Other formats can also be set in the same manner. separate data is stored in each signal format. Do not perform the switching below during data change.

  • Page 32: Screen Size Adjustment

    (7) Screen size adjustment a. Screen size HEIGHT Screen sizes are set through adjustments of HEIGHT and WIDTH. For these two pieces of data, the following four types (three types for HDTV) of size settings are available in a single 100% marker signal format.
  • Page 33 g. Adjustment procedure 5 (SDTV 4:3 UNDER, 16:9 UNDER scan) 1. Input signal HEIGHT • Monoscope for SDTV is recommended. 2. HEIGHT, WIDTH adjustments • First, select 4:3 using the ASPECT switch and then 4:3 marker WIDTH UNDER-SCAN using the U-SCAN switch. <HDTV 4:3 Scan Size>...

  • Page 34: Menu Functions

    4.5 Menu functions (1) Menu list All the functions are executable on menu screens. Table 4-5-1 Menu List Initial Page Contents Description value MENU1 <FORMAT> 1. MULTI-SDI FM* AUTO Sets an HD-SDI input format (for earlier version DKH-1051 only). 2. RGB/YPbPr FM HDTV Sets an RGB/YPbPr input format.

  • Page 35: Menu Operational Flowchart

    (2) Menu operational flowchart The switching between menus is done as follows when the MENU/ENT switch is pressed. <Normal Screen> Press MENU/ENT switch. Press MENU/ENT switch. MENU1 <FORMAT>->1080I/60 1.MULTI SDI FM AUTO 2.RGB/YPbPr FM HDTV 3.->1035I/1080I 1080I/60 4.->RGB/YPbPr YPbPr 5.INPUT DISP. Press MENU5 <LOCK>...

  • Page 36: Description Of Menu 1 Functions

    (3) Description of MENU 1 functions (4) Description of MENU 2 functions The vertical deflection frequency “/60” shown on the menu includes both “60 Hz” and ”59.94 Hz”. MENU2 <MODE> VER:01.1 1.CENT.MARKER 2.SYNC 3.UTILITY MODE INPUT MENU1 <FORMAT>->1080I/60 4.CHANGE ASPR. AUTO 1.MULTI SDI FM AUTO...

  • Page 37: Description Of Menu 3 Functions

    The following color temperatures are factory-set. The use of a serial remote controller (SRC-301A) allows you FILE Color temperature to remote-control up to 99 loop-through-connected Ikegami- REF. 6500K made monitors (17/18/20/30/80/90/HTM series) by setting an FILE1 6500K ID number for them, respectively.

  • Page 38: Description Of Menu 4 Functions

    25.4 G.GAIN 58.5 H.PHASE 47.3 CAUTION B.GAIN 32.6 TRAPE 52.7 R.BKG 52.0 SIDE P. If you forget your password, contact the nearest Ikegami dealer. G.BKG 52.0 B.BKG 55.1 We have a LOCK cancel password. NEXT (MENU) EXIT (ESC)(%) d. Set the LOCK state When the MENU/ENT switch is pressed after a password is a.

  • Page 39: Description Of Menu 7 Functions

    DKM-1051AV or DKM-1051AVD to the speaker built into Color temperature (x, y): 0.250 to 0.380 cd/m HTM-1005R from among CH1/2, CH3/4, CH5/6 and CH7/8. e. Measure and memorize white balance data b. Specify whether to display the audio level meter...

  • Page 40: Description Of Screen Messages

    If the power supply is not turned off during this period, the protection circuit will work to shut off the high voltage output, video output, etc. If this warning is given, turn off the power and contact the nearest Ikegami dealer.

  • Page 41: Installation And Removal Of Options

    5. Installation and removal of options 5.1 Installation procedures, installation examples and removal procedures for optional modules 1. Installation procedures and installation examples • Be sure to turn off the power before installing any optional module. The installation of any optional module with the power turned on may result in unexpected trouble or electric shock. •...

  • Page 42: Rack Mount Installation Drawing

    6. Rack mount installation drawing (1) XRM-744 installation drawing XRM-744 RACK MOUNT INDEX PARTS NAME PARTS No. Q'ty 1001 PACK MOUNT BASE M1-922857 1002 1-B, 2-B ADAPTOR BOARD M3-923834 1003 BRACKET M4-917704 (R) 1004 BRACKET M4-917704 (L) 1005 1-B, 3-C BAR NUT M4-907579 1006...
  • Page 43 (2) XRM-754 installation drawing XRM-754 RACK MOUNT INDEX PARTS NAME PARTS No. Q'ty 1001 RACK MOUNT BASE M1-922857 1002 ADAPTOR BOARD M3-923834 1003 BRACKET M4-917704 (R) 1004 BRACKET M4-917704 (L) 1005 7-B, 8-C BAR NUT M4-907579 1006 BLANK PANEL M2-909418 1007 SCREW MCF3-6FN...

  • Page 44: Rm-Htm-001 Installation Drawing

    (3) RM-HTM-001 installation drawing RM0HTM-001 RACK MOUNT INDEX PARTS NAME PARTS No. Q'ty 1001 RACK MOUNT BASE M1-922857 1002 ADAPTOR BOARD M3-923834 1003 BRACKET M4-917704 (R) 1004 BRACKET M4-917704 (L) 1005 4-B, 5-C BAR NUT M4-907579 1006 WFM BASE M2-924197 1007 FRONT PANEL M3-924195...

  • Page 45: Memo

    7. Memo It is recommended that various types of preset data be entered in the table below. Such data is useful for the management or restoration of data that is set up by experience in the field. DATA REF. FILE1 FILE2 FILE3 CHROMA...
  • Page 47 © Nov. 2003 by Utsunomiya Factory of Ikegami Tsushinki Co., Ltd. ■ All right reserved. Reproduction or Duprication, without permission of Ikegami Tsushinki Co., Ltd. of editional or contents in whole in part, any manner, is prohibited. ■ Specifications and design are subject to change without notice.
  • Page 48 Ikegami Tsushinki Co., Ltd. 5-6-16, Ikegami, Ohta-ku, Tokyo, Japan 146-8567 Phone:(03)5700-1111 Fax:(03)5700-1137 Ikegami Electronics (U.S.A.), Inc. HEAD QUARTERS: 37Brook Avenue, Maywood, New Jersey 07607 Phone : (201) 368-9171 Fax : (201) 569-1626 NORTHEAST OFFICE: 37Brook Avenue, Maywood, New Jersey 07607...

This manual is also suitable for:

Htm-1005ra

Table of Contents