Motion Control Engineering Motion 4000 Manual page 301

Motion 4000
Table 4.17 F7 Parameters
# Item
120 DNTS3 delta distance
121 DNTS3 delta low speed 0 fpm
122 DNTS3 delta high speed 0 fpm
123 DNTS4 speed
124 DNTS4 distance
125 DNTS4 delta distance
126 DNTS4 delta low speed 0 fpm
127 DNTS4 delta high speed 0 fpm
128 DNTS5 speed
129 DNTS5 distance
130 DNTS5 delta distance
131 DNTS5 delta low speed 0 fpm
132 DNTS5 delta high speed 0 fpm
133 Brake pick delay
134 Speed pick delay
135 Brake hold delay
136 Brake drop delay
138 Drive disable delay
139 Speed hysteresis delay 0 ms
140 Profile advance
141 Profile scale
142 Standard slew slope
143 Danger slew slope
144 Slew filter
145 Contract over-speed
146 Inspection over-speed
147 Leveling over-speed
148 Hoist-motor speed
149 Contract speed
150 High speed
151 Intermediate speed
152 Earthquake speed
153 Auxiliary speed
154 Backup power speed
Inspection speed
155
(normal)
Inspection speed
156
(reduced)
157 Correction speed
158 Leveling speed
Min Default
-120.0 in +6.0 in
0 fpm
0 fpm
0 fpm 0 fpm
-1200.0 in 0.0 in
-120.0 in +6.0 in
0 fpm
0 fpm
0 fpm 0 fpm
-1200.0 in 0.0 in
-120.0 in +6.0 in
0 fpm
0 fpm
0 ms 0 ms
0 ms +500 ms
0 ms +2000 ms
0 ms +500 ms
0 ms +1250 ms
+1000 ms
0 ms +100 ms
0% 100%
0.00 ft/s2 +0.49 ft/s2
0.00 ft/s2 +10.00 ft/s2 +50.00 ft/s2
+0.1 Hz +20.0 Hz
0 fpm +375 fpm
0 fpm +125 fpm
0 fpm +125 fpm
+1165.0
+1.0 rpm
rpm
+25 fpm +350 fpm
+25 fpm +350 fpm
+25 fpm +300 fpm
+25 fpm +150 fpm
+25 fpm +250 fpm
+9 fpm +200 fpm
0 fpm +50 fpm
0 fpm +50 fpm
0 fpm +75 fpm
0 fpm +4 fpm
F7: Parameters Adjust
Max
+120.0 in
+900 fpm
+900 fpm
+900 fpm
+1200.0 in
+120.0 in
+900 fpm
+900 fpm
+900 fpm
+1200.0 in
+120.0 in
+900 fpm
+900 fpm
+10000 ms
+10000 ms
+10000 ms
+2000 ms
+2000 ms
+10000 ms
+1000 ms
+1000%
+50.00 ft/s2
+20 Hz
+1000 fpm
+148 fpm
148 fpm
+9999.9 rpm
+800 fpm
+800 fpm
+800 fpm SPI1 terminal (TC-MPI board)
+150 fpm
+800 fpm SPI2 terminal (TC-MPI board)
+800 fpm Speed under generator power.
+148 fpm
+148 fpm
+250 fpm
+25 fpm
Notes
4-123
4