Cisco ASR 9000 Series User Configuration Manual page 79

Upgrading and Managing Cisco IOS XR Software
Info:
Info:
Info:
Info:
Info:
[y]|
Info:
Info:
(ctrl-c for options)
Info:
RP/0/RSP0/CPU0:router(admin)#SP/0/SM0/SP:
Jul
Info:
Info:
Info:
Info:
Info:
RP/0/RP1/CPU0:Jul
%INSTALL-INSTMGR-6-INSTALL_OPERATION_COMPLETED_SUCCESSFULLY :
Info:
Info:
Info:
Info:
Info:
rebooting .........................Initializing DDR SDRAM...found 4096 MB
Initializing ECC on bank 0Initializing ECC on bank 1
Initializing ECC on bank 2
Initializing ECC on bank 3
Turning off data cache, using DDR for first time
Initializing NVRAM...Testing a portion of DDR SDRAM ...done
Reading ID EEPROMs ............................
Initializing SQUID ...
Initializing PCI ...PCI0 device[1]: Vendor ID 0x10eePCI0 device[1]: Device ID 0x300ePCI1
device[1]:
Device ID 0x1100PCI1 device[1]: Vendor ID 0x1013PCI1 device[2]: Device ID 0x680PCI1 device[2]:
Vendor ID 0x1095PCI1 device[3]: Device ID 0x5618PCI1 device[3]: Vendor ID 0x14e4Configuring
MPPs ...
Configuring PCMCIA slots ...System Bootstrap, Version 1.53(20090311:225342) [CRS-1 ROMMON],
Copyright (c) 1994-2009 by Cisco Systems, Inc.
Acquiring backplane mastership ... successful
Preparing for fan initialization............. ready
Setting fan speed to 4000 RPMs
Released backplane mastership ...Board type is 0x100002 (1048578)
Switch 0 initialized
Switch 0 Port fe1: link up (100Mb Full Duplex Copper)
Enabling watchdogG4(7457-NonSMP-MV64360 Rev 3) platform with 4096 MB of main memory....
CARD_RACK_NUMBER: 0
RACK_SERIAL_NUMBER: TBC08052402
MBI Validation starts ... using Control Plane Ethernet.
DEBUG : Driving up signal strength for Intel LXT971
Our MAC address is 0005.9a3e.89da
Interface link changed state to UP.
Interface link state up.
MBI validation sending request.
HIT CTRL-C to abort
MBI validation sending request.
HIT CTRL-C to abort
MBI validation sending request.
HIT CTRL-C to abort
MBI validation sending request.
HIT CTRL-C to abort
MBI validation sending request.
HIT CTRL-C to abort
No MBI confirmation received from dSCboot: booting from
bootflash:disk0/asr9k-os-mbi-4.0.0/mbiasr9k-rp.vm
....................................................................................
##################################################################################
Restricted Rights LegendUse, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software
started by user 'lab' via CLI at 05:23:24 UTC Fri Jul 09 2010.\ 1% complete:
The operation can still be aborted (ctrl-c for options)
This operation will reload the following nodes in parallel:
0/RP1/CPU0 (HRP) (SDR: Owner)
0/SM0/SP (Fabric-SP) (Admin Resource)Proceed with this install operation (y/n)?
1% complete: The operation can still be aborted (ctrl-c for options)
Install Method: Parallel Reload/ 1% complete: The operation can still be aborted
The install operation will continue asynchronously.
9 05:36:41.152 : insthelper[62]: %INSTALL-INSTHELPER-6-RELOAD_NODE_INFO :
As part of install operation 7 this node (0/SM0/SP) will now reload.
The changes made to software configurations will not be persistent
across system reloads. Use the command '(admin) install commit' to
make changes persistent.
Please verify that the system is consistent following the software
9 05:36:43.962 : instdir[235]:
Install operation 7 completed successfully
change using the following commands:
show system verify
install verify packages
Install operation 7 completed successfully at 05:36:43 UTC Fri Jul 09 2010.
CARD_SLOT_NUMBER: 1
Cisco ASR 9000 Series Aggregation Services Router System Management Configuration Guide, Release 5.1.x
Upgrading to Cisco IOS XR Software Release 4.0
successfulReading backplane EEPROM ...
CPU_INSTANCE: 1
61