Commissioning - Bayrol PoolManager Chlorine User Manual

41

Commissioning

PoolManager has a menu for the first start-up. This menu covers all
®
parameters relevant to successful installation.
This menu for first start-up can be called up at any time as follows:
Service functions

The following steps are executed:
Action Entry
Step 1: Menu language
Configuration of menu language
Step 2: Set default values
Here, the desired default set Here, select the default set that best fits. In
can be selected and cases of doubt, please check all default
activated. values for their validity for the respective
installation.
For safety reasons, activation of the defaults
has to be confirmed at this point.
Step 3: System parameters
Configuration of pool and Pool volume of the connected swimming
system parameters pool.
Hose configuration of the pump hoses used.
This display is used to check the settings
made at the factory according to device
configuration.
Variation A: PoolManager Oxygen:
®
Step 4: Calibration
Calibration (comparison) of 1-point calibration pH. Please proceed as
measured pH value described in the section Calibration pH.
Step 5: Control parameters pH
Configuration of the most When refilling the pool, it may be sensible to
important parameters for expand the top and bottom pH value alarms
pH control and to adjust the p-range, as the pH value
can fluctuate somewhat during the starting
phase.
CAUTION: If the parameters are changed,
make absolutely sure that the values are set
back as soon as the pool water has
stabilised.
You can also use the configuration assistant.
Step 6: Manual dos. O2 (Bayrosoft )
®
Start manual dosing The dosing volume (for 0.5l Bayrosoft
water volume) is calculated upon entering the
pool volume and can be started here.
In order to increase the dosage volume for
the first dosage, thereby increasing the
certainty of disinfection, it's also possible to
select 2x or 3x the dosage volume.
Step 7: Dosage parameters O2
Configuration of the most Dosage volume is calculated by entering the
important parameters for pool volume and is displayed here to check
automatic Bayrosoft dosing. (0.5l Bayrosoft
®
be changed manually.
Select the dosage day such that it is directly
before the largest water usage expected
(e.g. high amount of swimming).
Temperature compensation ensures that
more Bayrosoft
temperatures (higher product consumption). It
should be set at least to normal.
Commissioning step by step

/10m
® 3
/10m water volume). It can
® 3
is dosed for higher water
®
Variation B: PoolManager Chlorine/Bromine
®
Step 4: Calibration
Calibration (comparison) of 1-point calibration pH. Please proceed as
measured value for pH and described in the section Calibration pH.
redox
1-point calibration mV (optional). Please
proceed as described in the section
Calibration redox (mV).
Step 5: Control parameters pH
Configuration of the most When refilling the pool, it may be sensible to
important parameters for expand the top and bottom pH value alarms
pH control and to adjust the p-range, as the pH value
can fluctuate somewhat during the starting
phase.
CAUTION: If the parameters are changed,
make absolutely sure that the values are set
back as soon as the pool water has
stabilised.
You can also use the configuration assistant.
Step 6: pH Value configuration
Possibility for automatically / Display shows the configured pH setpoint and
manually setting the pH value the current pH value in the pool water.
in the pool water
NOTE The pool water's pH value first has to
be set to pH 7.2 in order to facilitate
configuration of the redox value without issue.
Set pH operation mode to auto if
PoolManager
fully automated. This process will take some
time, depending on pool size and water
quality.
Set operating mode to manual if you would
like to configure the pH value via manual
addition of pH-elevator and -reducer.
Step 7: Manual dosing mV (Cl / Br)
Configure the desired The matching setpoint will depend on the
chlorine or bromine level and pool. It has to be calculated for the water in
calculate the associated the respective pool. Proceed as follows:
redox (mV) value
Set the pH value to pH 7.2
(see previous step)
Set the desired chlorine level in the pool via
manual dosing (or via manual addition of
chlorine) The volume of sodium hypochlorite
dosed is determined by PoolManager
the pool volume entered. This volume can be
overwritten manually.
Check the desired chlorine level via manual
measurement (DPD). The redox value in
[mV], which PoolManager
desired chlorine volume, is also the value that
has to be entered as the setpoint in the next
step.
Step 8: Control parameters redox (mV)
Configuration of the most Set the mV value as the setpoint you read in
important parameters for the previous step for the desired chlorine
redox control level. Adjust the bottom and top alarm
accordingly. Check the proportional range.
You can also use the configuration assistant.
In the individual menu pages, it is possible to scroll forward and
backward at any time.
For further information, please refer to the corresponding chapters in
this user's manual or to the help function on the device.
®
should make the configuration
®
via
®
shows for the
75