Service Functions; Management Of System Configurations; User Management; Menu User Management - Bayrol PoolManager Chlorine User Manual

21

Service functions

Required user qualification:
TRAINED SPECIALIST
The functions in the menu Service Functions may only
be used by a TRAINED SPECIALIST as defined in the
chapter User qualification.
The menu Service Functions is called up as follows:
Menu hotkey
Service Functions
This menu has special functions for service staff that are needed, for
example, for the system's basic configuration (pool volume,
configuration of dosing pumps, etc.).
Furthermore, a software update can be performed or the care method
(Cl / Br / O2) can be changed.
Specifically, the menu offers the following functions:
Menu Service Functions
Pool volume Pool volume in [m³]
Configuration of dosing Configuration of dosing pump parameters
pumps (Standard pump or membrane pump,
dosing capacity). See section Dosing pumps.
Device information Display of battery voltage
and test functions (Buffer battery for internal real-time clock),
future test functions.
Reset to defaults Reset of all parameter settings
to default settings.
Commissioning Call-up menu sequence for first commissioning.
Step by step See section Commissioning.
Software update Update of the PoolManager's
(from USB stick) To do so, the new software has to be copied to a
USB memory stick. See section Software update
(from USB stick).
Management of Import and export of complete system
system configurations configurations via remote access or USB stick.
See section

Management of system configurations.

Controller Model and Configuration of the PoolManager's
Care Method (Cl / Br / O2)
Trade show settings Activation of special functions for trade shows and
training sessions (e.g. internal simulation of
measured values)
Master level functions Special functions for users
with Master (level 4) access rights.
Separate documentation is available for these
functions as needed.
Use intelligent dosing Activate or deactivate intelligent dosing monitoring.
alarm If deactivated, the "classic" dosing time alarm is
used, i.e. a dosing time alarm is indicated, if the
setpoint has not been reached within the specified
max. dosing time.
Commissioning If set to On, PoolManager
On / Off the Commissioning sequence after power on.
This is the standard configuration for new
controllers from the factory.
21.1
This menu provides you with a wide range of options to load or save
entire system configurations. The source or destination can be a PC in
remote access or a USB memory stick. Furthermore, PoolManager
can also internally store four more configurations in addition to the
active configuration.
You can select one system configuration as the source and transfer it
into another system configuration (destination). The current active
system configuration can also be used as a source or a destination.
A system configuration includes all PoolManager
The only exclusions are:



An easy-to-follow name can be assigned to every copied configuration
in order to distinguish various configurations from each other.
22
PoolManager
administration. This makes it possible to define individualised access
rights for each of the system's users. Furthermore, the rights for
remote access can also be configured very flexibly for each individual
user. In doing so, it's even possible to make a distinction between
remote access from the local network and from the Internet, i.e. you
can release more functions for remote access from the local network
than for remote access from the Internet as needed.
22.1
The menu User Management is called up as follows:
internal software.
®
The menu contains multiple sub-menus with the following
configuration options:
Menu User administration
Standard users (menu access only)
This sub-menu can be used to configure access codes for standard users.
care method
® See section Standard users.
Individual users (menu & remote access)
This sub-menu can be used to create individual users and configure their
rights. Remote access from the local network or from the Internet can be
released for individual users.
See section Individual users.
Enable remote access for various functions
This sub-menu can be used to release or block certain functions for remote
access.
See section Enable remote access for various functions.
Enable remote access for add-on functions
This sub-menu can be used to release or block remote access for all add-on
functions.
See section Enable remote access for various functions.
will automatically start
®
Adjust user levels for various functions
This sub-menu can be used to set required user level for certain functions.
See section Adjust user level for functions.
The individual menus and functions are described in the detail in the
following sections.
Management of system configurations
Access data (usernames, access codes, passwords)
Care method
Network (IP) settings

User management

® delivers comprehensive, flexible, and powerful user

Menu User Management

Menu hotkey
User Management
®
parameter settings.
®
49