IDEC FC5A-F2M2 User Manual page 61

D A PID M
EVICE LLOCATION OF
+73 +150 Alarm 1 Hysteresis
+74 +151 Alarm 2 Hysteresis
+75 +152 Alarm 3 Hysteresis
+76 +153 Alarm 4 Hysteresis
+77 +154 Alarm 5 Hysteresis
+78 +155 Alarm 6 Hysteresis
+79 +156 Alarm 7 Hysteresis
+80 +157 Alarm 8 Hysteresis
+81 +158 Alarm 1 Delay Time
+82 +159 Alarm 2 Delay Time
+83 +160 Alarm 3 Delay Time
+84 +161 Alarm 4 Delay Time
+85 +162 Alarm 5 Delay Time
+86 +163 Alarm 6 Delay Time
+87 +164 Alarm 7 Delay Time
+88 +165 Alarm 8 Delay Time
+89 +166 AT Bias
+90 +167 Control Mode
Program Control Mode Start
+91 +168
Type
+92 +169 Step Time Unit
+93 +170 Program End Action
+94 +171 Proportional Term
Cooling Method
+95 +172
(CH0 only)
Set Point (SP) when Program
+96 +173
Control Starts
+97 +174 Number of Repeats
Cooling Output ON/OFF
+98 +175 Hysteresis
(CH0 only)
Output Type
+99 +176
(FC5A-F2M2 only)
External SP Input Bias
+100 +177
(CH1 only)
External SP Input Linear
+101 +178 Conversion Maximum Value
(CH1 only)
External SP Input Linear
+102 +179 Conversion Minimum Value
(CH1 only)
5-20
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
ODULE
When input range unit is Celsius:
0.1 to 100.0°C
When input range unit is Fahrenheit:
0.1 to 100.0°F
When input is voltage or current input:
1 to 1000
0 to 10000 sec
When input range unit is Celsius:
0 to 50 °C (0.0 to 50.0°C for input with decimal point)
When input range unit is Fahrenheit:
0 to 100 °F (0.0 to 100.0°F for input with decimal point)
0: Fixed value control mode
1: Program control mode
0: PV start
1: PVR start
2: SP start
0: Minute
1: Second
0: Terminate program control
1: Continue program control (Repeat)
2: Hold program control
0: Proportional band
1: Proportional gain
0: Air cooling
1: Oil cooling
2: Water cooling
When input is thermocouple or resistance thermometer:
Set point (SP) lower limit to set point (SP) upper limit
When input is voltage or current input:
Linear conversion min. to linear conversion max.
0 to 10000 times
When input range unit is Celsius:
0.1 to 100.0°C
When input range unit is Fahrenheit:
0.1 to 100.0°F
When input is voltage or current input:
1 to 1000
0: Non-contact voltage output (for SSR drive)
1: Current output
±20% of the external SP input linear conversion span
External SP input Linear conversion min. to input range
upper limit
Input range lower limit to external SP input linear conversion
max.
FC5A MicroSmart PID Module User's Manual FC9Y-B1283
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W