Table Of Contents - GE D30 Instruction Manual

Table Of Contents

Cautions And Warnings13
Inspection Procedure14
Introduction To The Ur15
Software Architecture16
System Requirements17
Configuring The D30 For Software Access18
Using The Quick Connect Feature21
Connecting To The D30 Relay26
Setting Up Cybersentry And Changing Default Password27
Mounting And Wiring28
Faceplate Keypad29
Relay Activation30
Commissioning31
Overview33
Security35
Iec 870-5-103 Protocol39
Order Codes With Process Bus Modules43
Replacement Modules45
Ur Signal Processing47
Protection Elements49
User Programmable Elements53
Monitoring54
Inputs55
Power Supply56
Communication Protocols58
Environmental60
Type Tests61
Approvals62
Panel Cutout63
Rear Terminal Layout69
Typical Wiring71
Dielectric Strength72
Ct/Vt Modules73
Process Bus Modules74
Contact Inputs And Outputs75
Transducer Inputs/Outputs86
Rs232 Faceplate Port88
Cpu Communication Ports89
Irig-B91
Description92
Fiber: Led And Eled Transmitters94
G.703 Interface96
Rs422 Interface99
Rs422 And Fiber Interface101
Ieee C37.94 Interface102
C37.94Sm Interface105
Introduction109
Enervista Ur Setup Main Window111
Settings Templates112
Securing And Locking Flexlogic Equations116
Settings File Traceability118
Faceplate121
Led Indicators122
Custom Labeling Of Leds125
Display130
Menus131
Changing Settings133
Settings Menu137
Introduction To Elements140
Introduction To Ac Sources141
Display Properties160
Clear Relay Records161
Communications162
Modbus User Map200
Fault Reports205
Oscillography207
User-Programmable Leds209
User-Programmable Self Tests212
Control Pushbuttons214
User-Programmable Pushbuttons216
Flex State Parameters220
User-Definable Displays221
Direct Inputs/Outputs223
Teleprotection231
Installation232
Remote Resources Configuration233
Ac Inputs234
Power System235
Signal Sources236
Breakers239
Disconnect Switches243
Flexcurves246
Introduction To Flexlogic253
Flexlogic Rules263
Flexlogic Example264
Flexlogic Equation Editor268
Flexelements269
Non-Volatile Latches274
Line Pickup276
Distance278
Power Swing Detect (Ansi 68)295
Load Encroachment305
Phase Current307
Neutral Current317
Ground Current325
Negative Sequence Current328
Voltage Elements335
Setting Groups345
Selector Switch347
Synchrocheck (Ansi 25)353
Autoreclose (Ansi 79)357
Digital Elements363
Digital Counters366
Monitoring Elements368
Contact Inputs378
Virtual Inputs380
Contact Outputs381
Virtual Outputs384
Remote Inputs386
Remote Double-Point Status Inputs387
Resetting388
Direct Inputs And Outputs389
Teleprotection Inputs And Outputs392
Iec 61850 Goose Analogs394
Iec 61850 Goose Integers395
Dcma Inputs396
Rtd Inputs397
Dcma Outputs399
Test Mode402
Force Contact Inputs403
Force Contact Outputs404
Actual Values Menu405
Flex States411
Direct Inputs412
Direct Devices Status413
Remaining Connection Status414
Metering Conventions416
Sources419
Synchrocheck422
Tracking Frequency423
Model Information430
Clear Records432
Relay Maintenance433
Relay Self-Tests435
Distance Characteristics444
Fast Distance Algorithm448
Memory Polarization449
Distance Elements Analysis450
Example456
Fault Type Determination463
Phase Distance468
Ground Distance469
Ground Directional Overcurrent473
Phase Distance Protection474
Replace A Module477
Replace Battery479
Dispose Of Battery481
Uninstall And Clear Files And Data484
Repairs485
Storage486
Disposal487
A.1.1 Flexanalog Items489
A.1.2 Flexinteger Items497
B.1.2 Physical Layer499
B.1.4 Modbus Rtu Crc-16 Algorithm500
B.2.1 Supported Function Codes502
B.2.3 Execute Operation (Function Code 05H)503
B.2.5 Store Multiple Settings (Function Code 10H)504
B.3.1 Obtaining Relay Files Via Modbus505
B.4.1 Modbus Memory Map507
B.4.2 Data Formats569
C.1.2 Communication Profiles605
C.1.3 File Transfer By Iec 61850606
C.2.1 Overview607
C.2.6 Mmxu: Analog Measured Values608
C.3.1 Buffered/Unbuffered Reporting610
C.3.6 Logical Node Name Prefixes611
C.4.1 Overview612
C.4.5 Ethernet Mac Address For Gsse/Goose615
C.5.1 Overview616
C.5.2 Configuring Iec 61850 Settings617
C.5.3 About Icd Files618
C.5.4 Creating An Icd File With Enervista Ur Setup622
C.5.6 Importing An Scd File With Enervista Ur Setup625
C.6.1 Acsi Basic Conformance Statement627
C.6.3 Acsi Services Conformance Statement628
C.7.1 Logical Nodes Table631
D.1.1 Overview635
D.1.3 Interoperability Document636
E.1.1 Interoperability641
E.1.2 Point List649
F.1.1 Dnp V3.00 Device Profile651
F.1.2 Implementation Table654
F.2.1 Binary Input Points658
F.2.2 Binary And Control Relay Output659
F.2.3 Counters660
F.2.4 Analog Inputs661
G.1.1 Radius Server Configuration663
H.1.1 Revision History665
H.1.2 Changes To The Manual666
H.2.1 Standard Abbreviations670
H.3.1 Ge Multilin Warranty673