Table of Contents
Advertisement
Cd.37
Skip command (
Skip function ................................................ 12-61
Skip function (Explanation of positioning terms)
.......................................................... Appendix-88
Skip operation program................................. 6-47
Slave axis (Explanation of positioning terms)
.......................................................... Appendix-88
Slot................................................................... 2-5
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
....................................................................... 5-28
Software stroke limit selection (
Software stroke limit upper limit value (
....................................................................... 5-28
Software stroke limit valid/invalid setting (
....................................................................... 5-28
S-pattern acceleration/deceleration processing
method......................................................... 12-82
S-pattern proportion (
Special start instruction (
Special start data instruction code setting value
Md.36
(
)...................................................... 5-130
Special start data instruction parameter setting
Md.37
value (
)............................................ 5-130
Special start repetition counter (
Specifications of input/output interfaces....... 3-16
Specifications of input/output signals ........... 3-12
Speed change (Explanation of positioning terms)
.......................................................... Appendix-88
Speed change 0 flag ................................... 5-126
Speed change function ............................... 12-37
Speed change program ................................ 6-20
Speed change request (
Speed control (Explanation of positioning terms)
.......................................................... Appendix-89
Speed designation during OP shift (
....................................................................... 5-56
Speed differential compensation (
Speed integral compensation (
Speed integral compensation (Explanation of
positioning terms) ............................. Appendix-89
Speed integral compensation changing ratio (
) .......................................................... 5-78
Pr.155
Speed limit function..................................... 12-23
Pr.8
Speed limit value (
) ............................ 5-158
Pr.13
Pr.14
) ..... 5-28
Pr.12
Pr.15
Pr.35
)...................... 5-38
Da.13
) .............. 5-101
Md.41
)... 5-132
Cd.15
) ............... 5-107
Pr.56
)
) .. 5-76
Pr.138
) ....... 5-64
Pr.117
) ............................ 5-26
Speed limit value (Explanation of positioning
terms) ................................................Appendix-89
Speed loop gain 1 (
Speed loop gain 2 (
Speed loop gain changing ratio (
Speed loop gain (Explanation of positioning terms)
...........................................................Appendix-89
Speed loop mode (Explanation of positioning
terms) ................................................Appendix-89
Speed-position function selection (
)
Speed switching mode (
Speed-position switching control (ABS mode)
)
........................................................................9-90
Speed-position switching control (INC mode)
)
........................................................................9-85
Speed–position switching control (Explanation of
positioning terms)..............................Appendix-89
Speed-position switching control movement
amount change register (
Speed-position switching control positioning
Md.29
amount (
Speed-position switching enable flag (
......................................................................5-148
Speed-position switching latch flag .............5-126
Speed-position switching signal ....................3-18
Speed-position switching control mode
(Explanation of positioning terms)....Appendix-89
Spiral interpolation .........................................9-60
SSCNET........................................................ A-14
SSCNET cable over all length.........................3-3
Standard speed switching mode ...................9-12
Start Hour (
Start complete (Explanation of positioning terms)
...........................................................Appendix-89
Start complete signal .....................................3-13
Start data No. (
Start data pointer being executed (
......................................................................5-132
Start details setting program..........................6-54
Start history ..................................................5-112
Start history pointer (
Start information (
Start Minute: second (
Start No. (
Index - 11
)..........................5-64
Pr.114
)..........................5-64
Pr.116
Pr.19
)..................5-32
Cd.23
).........................................5-124
Md.5
) ......................................5-112
Da.12
) ..............................5-101
Md.8
) .......................5-114
Md.3
) ............................5-112
Md.6
) .....................5-112
Md.4
).........................................5-112
) ....5-78
Pr.154
) .5-32
Pr.200
) ..............5-152
Cd.24
)
Md.43
)
Advertisement
Table of Contents
