Download  Print this page

Advertisement

SIMATIC IPC547E
SIMATIC
Industrial PC
SIMATIC IPC547E
Operating Instructions
09/2013
A5E32317120-AA
___________________
Preface
___________________
Overview
___________________
Safety instructions
___________________
Installing and connecting the
device
___________________
Commissioning the device
___________________
Monitoring functions of the
device
___________________
Expanding and assigning
parameters to the device
___________________
Device maintenance and
repair
___________________
Technical specifications
___________________
Technical support
___________________
List of abbreviations
1
2
3
4
5
6
7
8
A
B

Advertisement

   Summary of Contents for Siemens SIMATIC IPC547E

  • Page 1 ___________________ SIMATIC IPC547E Preface ___________________ Overview ___________________ Safety instructions SIMATIC ___________________ Installing and connecting the device Industrial PC ___________________ SIMATIC IPC547E Commissioning the device ___________________ Monitoring functions of the device Operating Instructions ___________________ Expanding and assigning parameters to the device...
  • Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
  • Page 3: Preface

    General knowledge in the field automation control engineering is recommended. Validity of the Operating Instructions These operating instructions are valid for all supplied versions of the SIMATIC IPC547E. Scope of this documentation The documentation for the SIMATIC IPC547E includes the following sections: ●...
  • Page 4 Preface SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 5: Table Of Contents

    DVD burner drive ......................... 45 4.4.2 System with two drives ........................ 46 4.4.3 RAID system ..........................46 4.4.3.1 RAID1 system ..........................46 4.4.3.2 RAID5 system ..........................47 4.4.3.3 RAID system with hot spare drive ....................47 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 6 Removing module of the redundant power supply ..............79 7.4.6 Removing the enclosure of the redundant power supply from the module ........ 80 7.4.7 Removing the motherboard......................80 7.4.8 Replacing the processor ......................82 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 7 Technical support ..........................119 Service and support ........................119 Troubleshooting ......................... 120 A.2.1 General information ........................120 A.2.2 RAID system and device startup ....................121 A.2.3 Notes on the use of third-party modules ..................122 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 8 Table of contents List of abbreviations ..........................123 Glossary .............................. 127 Index ..............................133 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 9: Overview

    Overview Product description The SIMATIC IPC547E is a powerful industrial PC in 19" rack format design (4 HE). It is perfectly suited for high-performance industrial PC applications. ● Maximum performance ● Attractive price Applications areas The SIMATIC IPC offers system integrators, cabinet designers, system engineers and machine designers a 19"...
  • Page 10 ● RAID1 – Disk mirroring on two drives, "hot swap" in connection with SATA removable drive bays ● RAID5 – Striping with parity on three drives, "hot swap" in connection with SATA removable drive bays ● Redundant power supply SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 11 Monitoring functions for program execution • Monitoring time can be parameterized in software • Restart can be parameterized in the event of a fault • Warnings can be analyzed by application program (local, via • LAN) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 12 You will find the languages that can be installed on the Recovery DVD. Language Microsoft Windows 7 Microsoft Windows Server Ultimate 2008 R2 German English French Italian Spanish Japanese Chinese Hong Kong Chinese (simplified) Chinese Taiwan Russian SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 13: Design Of The Device

    For removable drive bays with drives (HDD or SSD) or for 5.25" drives ⑦ 1 to 4 removable drive bays Depending on configuration, 1 to 4 removable drive bays with drives (HDD or SSD) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 14 See chapter "Ports and connections (Page 15)." ④ Dual-head graphics card DMS59 connection of dual-head graphics card ⑤ Expansion card slots • 4 × PCI • 2 × PCIe x16 • 1 × PCIe x8 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 15: Ports And Connections

    Connection for microphone, 3.5 mm phono jack ⑬ Dual-head graphics card DMS59 connection of optional dual-head graphics card The Ethernet interfaces are numbered on the enclosure to identify them clearly. The numbering by the operating system may deviate from this. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 16 DMS59 connector DMS59 connection ⑮ DVI-I connector DVI-I connections ⑯ VGA connector VGA connections Power supply connections The following figure shows the connections for the power supply for devices with single or redundant power supply. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 17: Operator Controls

    The alarm reset button is only available on devices with a redundant power supply. ① On/Off switch ② Alarm reset button can be used to switch off the warning signal SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 18 The On/off button is located on the front of the device behind the front door and is used to start and shut down the operating system. Additional information is available in the sections "Switching on the device (Page 41)" and "Switching off the device (Page 43)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 19: Status Displays

    The faulty drive could not be localized by the monitoring software. It may be possible to determine the defective drive with the RAID software, see section "RAID1 system (Page 46)" or "RAID5 system (Page 47)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 20 Power supply module is operating. If there is no redundancy, you will hear an acoustic signal permanently. Redundancy is in effect when both power supply modules are operating. Not lit: • Power supply module is out of service. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 21: Safety Instructions

    When you open the control cabinet, some areas or components may be carrying life- threatening voltages. If you touch these areas or components, you may be killed by electric shock. Switch off the power supply to the cabinet before opening it. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 22 • Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge, do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and protect from direct sunlight, moisture and condensation. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 23: Security Information

    ESD guideline (Page 95). Security information Siemens provides automation and drive products with industrial security functions that support the secure operation of plants or machines. They are an important component in a holistic industrial security concept. With this in mind, our products undergo continuous development.
  • Page 24 • If the device has a on/off button, assign the parameters of the function of the on/off button to meet your requirements under Windows. You can find the settings in the "Power Options" menu. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 25: Notes On Use

    Use in an industrial environment without additional protective measures The device has been designed for use in a normal industrial environment in accordance with IEC 60721-3-3 (pollutant class 3C2 for chemical influences, 3S2 for sand and dust). SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 26 Safety instructions 2.3 Notes on use SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 27: Installing And Connecting The Device

    The device may be damaged. Do not dispose of the original packaging. Pack the device during transportation and storage. 5. Check the contents of the packaging and any accessories you may have ordered for completeness and damage. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 28 7. Please keep the enclosed documentation in a safe place. It belongs to the device. You need the documentation when you commission the device for the first time. 8. Write down the identification data of the device. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 29: Device Identification Data

    ● COA label The COA label (Certificate of Authenticity) is located inside the front door and is only attached with pre-installed Windows operating systems. ● Component label The component label is located inside the front door. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 30: Mounting The Device

    (EN 60950-1:2006 and DIN EN 60950-1:2006-11) become void. Overheating can cause a fire. Proper functioning of the device is no longer guaranteed. Before you install the device, note the following general installation information. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 31: Mounting Location And Position

    You can order a Tower Kit for tower installation. ● Mounting on telescopic rails When telescopic rails are used for mounting, the device can be withdrawn fully from the cabinet or rack. Note the information in section "Telescopic rails (Page 107)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 32 For 600 mm cabinet: Threaded holes for type 3659.180 telescopic rails from the Rittal company For 800 mm cabinet: Threaded holes for type 3659.190 telescopic rails from the Rittal company ② Threaded holes for type 20110-072 telescopic rails from the Schroff company SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 33: Connecting The Device

    Ensure that the power outlet or shockproof power outlet of the building installation is freely accessible and as close as possible to the device, especially if the power plug is secured by a power plug latch. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 34: Connecting Peripheral Equipment

    Hot-plug I/O devices (USB) may be connected while the PC is in operation. NOTICE Non-hot-plug I/O devices I/O devices that do not support hot-plugging may not be connected until the device is powered off. Strictly adhere to the specifications for peripheral equipment. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 35: Connection Of Equipotential Bonding

    The equipotential bonding connection on a device has a large surface and makes contact over a large area. The equipotential bonding connection is identified by the following symbol: Requirement ● T20 screwdriver SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 36: Connecting The Power Supply

    IEC 62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are identified with the classification "VFI-SS-.." or "VI-SS-..". Note The power supply of the device contains a PFC (Power Factor Correction) circuit to conform to the EMC directive. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 37 Use a flexible cable with UL approval and CSA marking as well as the following features: ● Type SJT with three conductors ● Conductor cross-section ≥ 18 AWG ● Cable length ≤ 4.5 m ● Tandem grounding-type plug 15 A, ≥ 250 V SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 38 4. Switch on the on/off switch To prevent unintentional removal of the power cable, you can secure the plug as follows: ① 1. Remove the retaining screw ② 2. Screw on the latch for the power plug SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 39 To prevent unintentional removal of the power cable, you can secure the power plug as follows: ① 1. Remove the retaining screws ② 2. Screw on the latch for the power plug SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 40: Connecting The Device To Networks

    You can operate up to five monitors simultaneously at the interfaces of the integrated graphics controller in combination with the optional graphics card. Parameter assignment is performed by means of the Control Panel in Windows. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 41: Commissioning The Device

    1. Switch the on/off switch to position I. Information on the position of the switch is available in the section "Operator controls (Page 17)". 2. Press the on/off button. The"POWER" LED lights up. The module carries out a self-test. Then Windows is started. 3. Follow the instructions on the screen. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 42: Automatic Startup Of The Device Depending On The Bios Entry

    20 seconds. Automatic startup may endanger the operation of the machine or plant, for example, after a power failure. Take the BIOS Setup entry "Power Failure Recovery" into consideration in the plant planning. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 43: Windows Security Center

    For non-Windows operating systems: ● Briefly press the on/off button. The operating system is shut down. The "POWER" LED goes out. The device is switched off but not fully disconnected from the mains voltage. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 44 Data on the drive may be lost. The device may be damaged. Perform a hardware reset only in the case of an emergency. For all operating systems: ● Press the on/off button for more than 4 seconds. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 45: Information On Optional Features

    Data comparison is the only guarantee that data has been written correctly. Perform data comparison each time you burn a disc. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 46: System With Two Drives

    For information on the mounting positions, refer to section "Replacing a defective hard disk drive in the RAID system (Page 70)". Additional information on RAID1 systems can be found in the section "Managing RAID systems (Page 57)." SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 47: Raid5 System

    "Replacing a defective hard disk drive in the RAID system (Page 70)". ● Information on integration of a replaced hot spare drive into the RAID system is available in the section "Integrating a hot spare hard disk drive in the RAID system (Page 62)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 48 Commissioning the device 4.4 Information on optional features SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 49: Monitoring Functions Of The Device

    The SIMATIC IPC DiagMonitor software offers additional alarm and linking options in addition to the local monitoring functions of the SIMATIC IPC DiagBase software and includes: ● The software for the stations to be monitored. ● A library for creating user-specific applications. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 50: Temperature Monitoring And Temperature Display

    The operation of the front, CPU and power supply fans is monitored. If a fan fails, the following reactions are triggered: ● The "FAN" status display lights up red. ● If the SIMATIC monitoring software is installed, a fan alarm is output. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 51: Watchdog (wd)

    The "Reset on" option immediately triggers a hardware reset that may result in loss of data under Windows. WD monitoring times The monitoring time can be configured with the DiagBase or DiagMonitor software. Note When you change the monitoring time, the change becomes effective immediately. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 52: Battery Monitoring

    The warranty does not cover a reset of the hardware in the event of a loss of a password. Please store the password carefully and make sure it is protected against unauthorized access. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 53: Expanding And Assigning Parameters To The Device

    ● The front door is open. Procedure 1. Press the marked hooks at the same time to release the front panel. 2. Swivel the front panel in the direction indicated and lift it off. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 54: Open The Device

    Limitation of liability All technical specifications and approvals apply only to expansions which are approved by the Siemens AG. We are not liable for functional limitations caused by the use of third-party devices or components. Observe the installation instructions for the components. UL approval of the device only applies when UL-approved components are used according to their "Conditions of...
  • Page 55: Memory Expansion

    If the height is exceeded, you may experience contact problems, malfunctions and difficulties with the assembly. You can find the permitted dimensions for expansion cards in the chapter "Dimensional drawing for the installation of expansion cards (Page 99)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 56 7. Secure the card retainer with the screw If you are installing a short expansion card, remove the locking screw from the card retainer and install it in the opposite hole. 8. Close the device. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 57: Device Maintenance And Repair

    Device maintenance and repair Managing RAID systems 7.1.1 Example for a RAID1 system during the boot phase of the system 7.1.2 Example for a RAID5 system during the boot phase of the system SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 58: Raid Software

    1. Select the RAID software via "Start > Programs > Intel Rapid Storage Technology". 2. Select "Manage" > "Advanced" to display details about the RAID1 system. 3. Select the "Help > "System Report" > "Save" command to create a report with details about the RAID1 system. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 59: Checking The Status Of The Raid System

    The functioning hard disk is indicated by BIOS with its port number or by the RAID software with its device port number. The following figure shows the corresponding window in the RAID software with a RAID1 system. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 60: Points To Note If The Hard Disk In The Raid System Is Replaced When The Computer Is Turned Off

    To be able to boot from the RAID system (RAID1 or RAID5), you must place it first in the list of bootable sources in the BIOS "Boot" setup menu. Otherwise, the system will boot from the hard disk drive you have just installed and the message "Operating system not found" will be displayed. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 61: Integrating A New Hard Disk Drive In The Raid System

    Pressing the "Rebuild to another Disk" link initiates synchronization of the RAID system (RAID1 or RAID5). A defective hard disk drive is still displayed during the rebuilding process. This display disappears when the rebuilding process is completed. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 62: Integrating A Hot Spare Hard Disk Drive In The Raid System

    Drives 3 years Backup battery 5 years Device fan 3 years Filter pad Depending on the degree of soiling Information on ordering replacement parts is available in the chapter "Service and support (Page 119)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 63: Changing The Filter Pad

    RF suppression. Contact your technical support team or where you purchased your PC to find out which system expansion devices may be installed. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 64 ● T20 screwdriver for protective conductor connection and enclosure ● T6 screwdriver for removing and installing the DVD drive ● T10 screwdriver for all of the remaining screws See also Spare parts and repairs (http://support.automation.siemens.com/WW/view/en/16611927) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 65: Removing And Installing Hardware Components

    ● The device is open, see the section "Open the device (Page 54)". ● The front door is open, see chapter "Opening the front door (Page 53)". Procedure Removal 1. Remove the highlighted screws. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 66 3. Hold the drive cage using the highlighted areas, move it in the direction of the arrow and lift it out completely from the device. Installation Follow the steps described under removal in the reverse order. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 67: Removing And Installing The Hard Disk Drive From The Removable Drive Bay

    2. Use the appropriate key to unlock the tray on the removable drive bay. 3. Open the handle on the removable drive bay and open it at the highlighted spot in direction of the arrow until you feel a slight resistance. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 68 Make sure that the tray is completely inserted into the removable drive bay. 5. Close the handle and lock the tray. Note The tray must always be locked in the removable drive bay to ensure reliable operation of the devices with removable drive bays. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 69: Removing And Installing An Internal Hard Disk Drive

    ● The device is fully disconnected from the mains voltage, see chapter "Switching off the device (Page 43)". ● The device is open, see the section "Open the device (Page 54)". ● T10 screwdriver SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 70: Replacing A Defective Hard Disk Drive In The Raid System

    Replace the drive in the removable drive bay when the "HDD" status display of the device is not lit. Observe the ESD guideline (Page 95). Always replace the drive with a new drive of the same type and capacity. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 71 The following tables include information on the alarms of the status displays. If the hard disk drive is defective and the SIMATIC monitoring software is installed, the LEDs of the status display light up individually or simultaneously. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 72 ① Removable drive bay 0 ② Removable drive bay 1 ③ Removable drive bay 2 ④ Removable drive bay 3 ⑤ "Power" LED; power supply available ⑥ "HDD" LED, access to hard disk drive SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 73: Installing A 5.25" Front Hard Disk Drive

    ● The device is fully disconnected from the mains voltage, see chapter "Switching off the device (Page 43)". ● The drive cage has been removed, see chapter "Removing and installing the drive cage (Page 65)". ● T10 screwdriver SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 74 The following figure shows the possible positions of the screws on the right side of the drive cage. 4. Install the drive cage back into the device, see section "Removing and installing the drive cage (Page 65)". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 75: Removing And Installing A Dvd Drive

    The following figure shows the positions of the screws on the fan side of the drive cage. The following figure shows the positions of the screws on the drive cage on the outside of the device. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 76: Removing The Device Fan

    ● The front panel is removed, see section "Removing the front panel (Page 53)". ● The device is open, see the section "Open the device (Page 54)". ● T20 screwdriver ● A fan Use only a fan of the same type. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 77 Two small arrows are shown on the device fan. These indicate the rotating direction of the fan and the direction of the airflow. Install the fan in such a way that the arrow for the direction of the airflow points to the interior of the enclosure. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 78: Replacing The Backup Battery

    ● An identical lithium battery or a type recommended by the manufacturer Information on original spare parts for SIMATIC IPCs is available at SIMATIC IPC after- sales information system (http://www.siemens.com/asis). Procedure 1. The location of the backup battery on the motherboard and the procedure for replacing it are described in the manual of the motherboard on the supplied "Documentation and...
  • Page 79: Removing Module Of The Redundant Power Supply

    ● The device is fully disconnected from the mains voltage, see chapter "Switching off the device (Page 43)". ● T10 screwdriver Procedure 1. Remove the screws highlighted in the first figure. 2. Pull out the power supply module from the enclosure using the handle. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 80: Removing The Enclosure Of The Redundant Power Supply From The Module

    (Page 43)". ● The device is open, see the section "Open the device (Page 54)". ● A motherboard The motherboard as spare part is supplied without processor and memory modules. ● T10 screwdriver SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 81 1. For installation, follow the steps for removal in reverse order. 2. Update the BIOS to match the version of the motherboard. Note during the update if you are operating a device with or without RAID system. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 82: Replacing The Processor

    Only an approved processor is permitted to be installed on the motherboard of the device. Information about original spare parts for SIMATIC IPCs is available on the Internet at: – SIMATIC IPC after-sales information system (http://www.siemens.com/asis) – Contacts (http://www.siemens.com/automation/partner) ● Manual of the motherboard on the supplied "Documentation and Drivers" DVD.
  • Page 83 If the installed processor is operated with a higher clock frequency than permitted, it can be destroyed or cause loss of data. Operate the processor only at a clock frequency that is equal to or less than the permitted clock frequency. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 84: Installing The Software

    Note Before you install new drivers or operating system updates for Windows MUI versions, configure the regional menu and dialog settings and the default English (US) language. Other operating systems Contact the corresponding manufacturer. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 85: Installing Drivers And Software

    Installing the software ● You can find information about installing SIMATIC software packages in the corresponding documentation. ● You can obtain information about driver updates and installing application programs from the respective manufacturers. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 86: Installing Windows 7 Or Windows Server 2008 R2

    Press any key to boot from CD or DVD .. After a few seconds, you will see the "Install Windows" installation program. 8. Now follow the instructions in the installation program. You can find additional information on this in the next section. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 87 Please read the information in the section "Information for systems with RAID or AHCI controller". Drive options For display of additional functions that you can use to set up the data medium, (advanced) see figure "Windows installation window "Drive options (advanced)"". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 88 Integrate this driver before you partition the data medium and before you install the operating system. For more information on integrating the storage controller, refer to the section "Information for systems with RAID or AHCI controller". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 89: Setting Up The Language Selection Using The Multilanguage User Interface (mui)

    For this purpose, you can either select one of the preinstalled languages or install a new language package. The following command sequences are described in English. Depending on the default setting, they can be displayed in another language. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 90 1. Choose: "Start > Control Panel > Clock, Language, and Region > Regional and Language Options" 2. Select the "Keyboards and Languages" tab. 3. Click the "Install/uninstall languages" button and make the required changes. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 91: Restoring The Delivery State

    All data on drive C: will be completely deleted, reformatted and overwritten with the original factory software. If "Restore entire drive" is set ALL data, user settings, authorizations or license keys will be lost on the entire drive. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 92: Installing Raid Controller Software

    (images). SIMATIC IPC Image & Partition Creator supports the burning of DVD media only. You can order the tool using the Siemens online ordering system (http://www.siemens.com/automation/mall). For more information about SIMATIC IPC Image & Partition Creator, refer to its product documentation.
  • Page 93: Technical Specifications

    If the device is supplied with installed software, observe the corresponding license agreement. UL approval The following approvals are available for the device: ● Underwriters Laboratories to Standard-UL 60950-1, File no. E11 5352 ● Canadian National Standard CAN/CSA-C22.2 No. 60950-1-07 (I.T.E) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 94 This product meets the requirements of Korean certification. This product satisfies the requirement of the Korean Certification (KC Mark). 이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 95: Directives And Declarations

    Directive". Compliance with this standard has been verified according to EN 60950-1:2006 + A11:2009 +A1:2010 +A12:2011. 8.2.3 Declaration of conformity The corresponding documentation is available on the Internet at: SIEMENS Industry Online Support (http://support.automation.siemens.com/WW/view/en/10805661/130000). Navigate to your device in the left display area in the tree structure under "Industrial PC". 8.2.4...
  • Page 96 These values conform to the specifications of IEC 61000-4-2. ① Synthetic materials ② Wool ③ Antistatic materials such as wood or concrete SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 97 This way, the discharge energy does not reach and damage the sensitive components. – Discharge your body electrostatically before you take a measurement at a module. Do so by touching grounded metallic parts. Always use grounded measuring instruments. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 98: Dimension Drawings

    Technical specifications 8.3 Dimension drawings Dimension drawings 8.3.1 Dimension drawing of the device Front view and plan view SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 99: Dimensional Drawing For The Installation Of Expansion Cards

    Technical specifications 8.3 Dimension drawings 8.3.2 Dimensional drawing for the installation of expansion cards 8.3.3 Dimension drawing for the drilling holes of telescopic rails SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 100: Technical Specifications

    Current delivery (DC) +5 V/26 A, +3.3 V/24 A; in total 190 W permitted +12 V/15 A; +12 V/15 A; –12 V/0.2 A; +5 Vaux/2 A The total sum of all voltages is max. 230 W. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 101 1 V/m, 2 to 2.7 GHz • 80% AM to IEC 61000-4-3 10 V, 150 kHz to 80 MHz • 80% AM to IEC 61000-4-6 Magnetic field 30 A/m, 50 Hz/60 Hz (to IEC 61000-4-8) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 102 When using a hard disk drive in a removable drive bay, the device should generally be free of mechanical disturbances. When using a DVD burner, the device should generally be free of mechanical disturbances during burning. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 103 12 V; 2.1 A • 3.3 V ; 0.4 A • Power consumption per slot, permitted ≤ 25 W Power loss all slots, permitted ≤ 80 W Total 3.3 V current may not exceed 1.2 A. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 104 DisplayPort 2560 × 1600 at 60 Hz, 32 bit color depth – DVI 1920 × 1200 at 60 Hz, 32 bit color depth – VGA 2048 × 1536 at 60 Hz, 32 bit color depth Adapter for VGA and DVI-D supplied SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 105 Switch Fault Tolerance (SFT) • Audio Realtek ALC671, 6-channel DAC support Micro • Line In • 2 W at 4 Ω Line Out • AMT and teaming cannot be used simultaneously on the Ethernet interface. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 106: Power Demand Of The Components

    +5 V 2.5 A + 5%, – 3% The total output of the +5 V and +3.3 V voltage must be ≤ 190 W. The inrush current is: ● ≤ 80 A for 3.6 ms SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 107: Redundant Power Supply

    M5 x 6 mm The mounting screws of the telescopic rails may not protrude by more than 5 mm into the enclosure. See also Dimension drawing for the drilling holes of telescopic rails (Page 99) SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 108: Hardware Description

    3. Open the application. 8.5.3 Interrupt assignment Interrupt assignment depending on operating system The functions are assigned different interrupts (IRQ), depending on the operating system. A distinction is made between the PIC and APIC modes. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 109 IRQ A to H is assigned to IRQ 0 to 15 automatically by the BIOS in PIC mode. A specific assignment cannot be forced. Interrupt PIC and APIC mode Interrupt APIC mode BIOS Default Interrupt PIC mode, e.g. DOS SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 110 PCI-IRQ A to H is assigned to IRQ 0 to 15 automatically by the BIOS in PIC mode. A specific assignment cannot be forced. Interrupt APIC mode BIOS Default Interrupt PIC mode, e.g. DOS SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 111: Setting The Bios

    Drivers" DVD that ships with the manual. Note After a BIOS update, you need to execute the "Restore Defaults" command. Executing the "Restore Defaults" command restores all BIOS settings to their original state. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 112: Description Of Active Management Technology

    An ISO file contains a memory image of the content of a CD or DVD structured in the ISO 9660 format. ● Remote reboot An AMT PC can be booted remotely from a bootable ISO file made available by another SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 113 SIMATIC IPC Remote Manager The "SIMATIC IPC Remote Manager" software is available for utilization of the AMT functions with SIMATIC IPCs. The software can be ordered from the Siemens online ordering system "Industry Mall (http://mall.automation.siemens.com)". For detailed information about "SIMATIC IPC Remote Manager", refer to the corresponding product documentation.
  • Page 114: Amt Basics

    BIOS setup. Afterwards the Intel Management Engine (Intel ME) has to be activated ® ® and set for AMT. Set the following in the Management Engine: ● Configure network for access via AMT ● Create password SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 115: Overview Of Amt

    5. Exit the BIOS with the <F10> key "Save and Exit". The AMT PC starts. 6. To access the MEBx, press the <Ctrl+P> keyboard shortcut at system power-up. 7. In the login dialog, enter the standard password "admin". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 116: Advanced Settings

    <Fully qualified domain name>:16993" and for unencrypted connections "http://<IP address>:16992". ● WinRM: A command line program that is part of Windows as of Windows Vista. This tool can be downloaded for older Windows versions. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 117: Reset Amt With Unconfigure Me

    3. After the start, a user prompt appears asking whether you really want to discard all the settings in the Management Engine. 4. Confirm with "Y". On a German keyboard, this means pressing the <Z> key. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 118: Determining The Network Address

    2. Select the value "KVM" for "User Consent". To allow a user with administrator privileges to avoid this code query, follow these steps: 1. Select "Intel(R) AMT Configuration > User Consent" in the MEBx. 2. Enable "Opt-in configurable from remote IT". SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 119: Technical Support

    You can find additional information and support for the products described on the Internet at the following addresses: ● Technical support (http://www.siemens.de/automation/csi_en_WW) ● Support request form (http://www.siemens.com/automation/support-request) ● After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) ● SIMATIC Documentation Collection (http://www.siemens.com/simatic-tech-doku-portal) ● Your local representative (http://www.automation.siemens.com/mcms/aspa-db/en/Pages/default.aspx) ●...
  • Page 120: Troubleshooting

    BIOS Setup. 2. Set the time and date in the setup menu. Although the BIOS setting is The backup battery is dead. Replace the backup battery. OK, the time and data are still wrong SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 121: Raid System And Device Startup

    After changing the drive, System was booted without Reboot the system with a functioning drive. "unused" is indicated for the functioning drive. The relevant SATA port removable drive bay might not be switched on. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 122: Notes On The Use Of Third-party Modules

    Different pin assignment • module being used was the cause of the fault. Replace the thrid-party module with a Siemens module or contact the module supplier. If the device still crashes, contact your technical support team. Insufficient output of an external Use a higher capacity power supply power supply, e.g., UPS...
  • Page 123 Operating system without GUI Digital Versatile Disk Digital versatile disk Digital Visual Interface Digital display interface DVI-I Digital Visual Interface Digital display interface with digital and VGA signals Extended capability port Extended parallel port SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 124 Programmable interrupt controller Preboot Execution Environment Software for running new PCs without drive data via the network RAID Redundant Array of Independent Disks Redundant drive array Random Access Memory Read-Only Memory SDRAM Synchronous DRAM SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 125 German Electrical Engineers) Video Graphics Array Video adapter which meets industrial standard Virtualization Technology Intel technology with which a virtually closed environment can be made available Watchdog Program monitoring with error detection and alarming SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 126 List of abbreviations SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 127: Glossary

    Located on the motherboard, connects the processor with the RAM, the graphics controller, the PCI bus, and the external interfaces. Configuration files These are files containing data which define the configuration after restart. Examples of such files are CONFIG.SYS, AUTOEXEC.BAT and the registry files . SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 128 This can be configured in Windows by selecting Settings > Control Panel > Energy options. Ethernet Local network (bus structure) for text and data communication with a transfer rate of 10/100/1000 Mbps. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 129 The devices connected to a LAN are called nodes. The purpose of networks is the mutual use of files, ers or other resources. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 130 Glossary License key The license key represents the electronic license stamp of a license. Siemens provides the license keys for protected software. Module Modules are plug-in units for PLCs, programming devices or PCs. They are available as central modules, interface modules, expansion cards or mass storage (mass storage module).
  • Page 131 300 Mbps. Session-At-Once In session-at-once, the CD can be written to both with an audio session and a data session. The two sessions are written to at once (as in disc-at-once). SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 132 In track-at-once recording, a CD can be written to in bits in several sessions if the CD was not closed. Wake on LAN Wake on Local area network. This function allows the PC to be started via the LAN interface. SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 133: Index

    COA label, 29 Technical specifications, 104 COM1 Types and mounting locations, 11 Connection, 15 Dust protection, 101 COM1 port DVD drive Technical specifications, 105 Removing and installing, 75 COM2 DVI-I Connection, 15 Connection, 15, 16 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 134 68 LEDs, (Status displays) remove from drive bay, 67 License key, 91 Second hard disk drive, (See System with two Limitation of liability, 64 drives) Hardware reset, 44 Connection, 15 LPT1, 105 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 135 Removing, 27 Status displays of the hard disk drives, 73 Power consumption, 100 RAID5 system with hot spare drive, 47 Power plug latch, 38, 39 Rating plate, 29 Power requirements, 106 Real-time protection, 43 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...
  • Page 136 Disconnect from mains voltage, 44 Forced shutdown, (Hardware reset) Hardware reset, 44 Shutting down the operating system, 43 Switching on the device Configure automatic startup, 42 Switching on for the first time, 41 System partition, 91 SIMATIC IPC547E Operating Instructions, 09/2013, A5E32317120-AA...

Comments to this Manuals

Symbols: 0
Latest comments: