Siemens SIMATIC IPC520A Quick Install Manual

1
Mounting the device
1.1 Before mounting and commissioning
IMPORTANT: observe all documents enclosed with the device and the operating instructions manual
before mounting and connecting the device. You find the complete documentation of the device on
the Siemens Industry Online Support (http://www.siemens.com/simatic-ipc-doku-portal).
The manual symbol refers to detailed information in the operating instructions.
1.2 Scope of delivery
One SIMATIC IPC520A device, one mounting accessory kit including one DC connecting terminal block,
one standard rail bracket, two wall mounting brackets and eight screws. No accessories such as Micro SD
card or cables.
1.3 Valid mounting positions
Horizontal mounting
Free space required around the device
50 mm
100 mm
Mounting the device
1.4
Ensure that the mounting surface on the wall can bear four times the total weight of the device,
including fixing elements.
Use only the anchors and screws specified in the operating instructions.
Mounting on DIN rails
1
Wall mounting
Torque: 0.8 Nm
1
2
Connecting the device
2.1 Connecting the protective earth
1
M4
Desk mounting
45 °C
0 °C
50 mm
100 mm
2
T10
2
Torque: 0.8 Nm
2
T10
2
2.5 mm² = AWG14
2
T20
Torque: 1.5 Nm
2
Connecting the device
2.2
Connecting the power supply
The device must only be connected to a 24 V DC power supply which satisfies the requirements
of safety extra low voltage (SELV) or protective extra low voltage (PELV) according to
IEC/EN/DIN EN/UL 61010-2-201.
1
/OFF
Tightening torque: 0.56 Nm
Wire cross-section: 2.5 mm²
Rated temperature of wire: 70℃
Conductor material: Cu
2.3 Switching on the device
Set the on/off switch to position " " (ON). The "PWR" LED lights up.
Note:
Operating System is not installed in new device.
/ON
3
Installing OS and SDK components
3.1 Flashing the Ubuntu Operating System
Install NVIDIA SDK Manager on a local PC. For detailed installation procedures,
1
refer to the NVIDIA website (https://docs.nvidia.com/sdk-manager/index.html)
scan the QR code on the right.
Set IPC520A to Force Recovery Mode (RCM).
2
1. Switch off IPC520A.
2. Connect the IPC520A to the local PC through a micro USB cable.
3. Keep pressing the Reset button of IPC520A.
4. Switch on the IPC520A and wait for more than 3 seconds, then release the Reset button.
5. Check whether the IPC520A is entering the RCM:
Enter the commend "lsusb" on the local PC terminal, then the output returns should be as below:
Bus <xxx> Device <xxx>: ID 0955: <7e19> Nvidia Corp
Otherwise, redo step .
2
Start up NVIDIA SDK Manager, and register an NVIDIA account to log in to NVIDIA SDK Manager.
3
Follow below steps to flash the Ubuntu Operating System. For detailed configuration procedures,
4
refer to the NVIDIA website (https://docs.nvidia.com/sdk-manager/install-with-sdkm-jetson/index.html)
or scan the QR code on the right.
• STEP 01 DEVELOPMENT ENVIRONMENT:
In the pop-up window, select "Jetson Xavier NX (P3668-0001 module)" radio button
as the Target Hardware and click "OK" button; select jetpack version supported by
IPC520A as the Linux version, and then click the "CONTINUE TO STEP 02" button.
Note: You can get the version compatibility and supported jetpack version information from Siemens
Industry Online Support website (https://support.industry.siemens.com/cs/ww/en/view/109783704).
• STEP 02 DETAIL AND LICENSE:
Click the checkbox before "Jetson OS" under the "TARGET COMPONENTS"; enable the checkbox to
accept the terms and conditions of the license agreements, and then click "CONTINUE TO STEP 03"
button.
• STEP 03 SETUP PROCESS:
Select "Manual Setup - Jetson Xavier NX" option to put your device into Force Recovery Mode, and
then click the "Flash" button to flash your Jetson Xavier NX module through NVIDIA SDK Manager.
• STEP 04 SUMMARY FINALIZATION:
Check the flash result. If the status of component Flash Jetson OS is "Success", the flashing is finished.
Reboot the IPC520A. When you boot the first time, the IPC520A will take you through some initial
5
setup.
3
2
0.5 x 3
or