Multispeed Select Setting (Cf1 To Cf4 And Sf1 To Sf7) - Hitachi SJ700D-004L Instruction Manual

Chapter 4
Data Description
51 F-TM: Forcible-terminal operation
52 ATR: Permission of torque command input
53 KHC: Cumulative power clearance
54 SON: Servo On
55 FOC: Forcing
56 MI1: General-purpose input 1
57 MI2: General-purpose input 2
58 MI3: General-purpose input 3
59 MI4: General-purpose input 4
60 MI5: General-purpose input 5
61 MI6: General-purpose input 6
62 MI7: General-purpose input 7
63 MI8: General-purpose input 8
65 AHD: Analog command holding
66 CP1: multistage position settings selection 1
67 CP2: multistage position settings selection 2
68 CP3: multistage position settings selection 3
69 ORL: Zero-return limit function
70 ORG: Zero-return trigger function
71 FOT: forward drive stop
72 ROT: reverse drive stop
73 SPD: speed / position switching
74 PCNT: pulse counter
75 PCC: pulse counter clear
82 PRG: EzSQ program run
no NO : no function
(*1) Refer to programing software EZ-SQ user manual.
4.2.40 Input terminal a/b (NO/NC) selection
The input terminal a/b (NO/NC) selection function allows you to
specify a-contact or b-contact input for each of the intelligent input
terminals [1] to [8] and the FW terminal.
An a-contact turns on the input signal when closed and turns it off when opened.
An b-contact turns on the input signal when opened and turns it off when closed.
The terminal to which the reset (RS) function is assigned functions only as an a-contact.
Item
Terminal active state
Terminal [FW] active state

4.2.41 Multispeed select setting (CF1 to CF4 and SF1 to SF7)

The multispeed select setting function allows you to set multiple
motor speeds and switch among them by way of signal input via
specified terminals.
Multispeed operation can be performed in two modes: binary
operation mode (with up to 16 speeds) using four input terminals
and bit operation mode (with up to eight speeds) using seven input
terminals.
Item Function code
Multispeed operation
selection
Multispeed 0 to 15
settings
Carefully note that during multispeed operation, the rotation direction specified in an operation command is reversed
if the sum of the frequencies specified by the main frequency and auxiliary frequency commands is less than 0 Hz
when the following settings have been made:
- The control circuit terminal block (01) is specified for the frequency source setting (A001).
- The external analog input (O/O2/OI) mode, set by a combination of [AT] selection (A005), [O2] selection (A006), and
AT terminal On/Off state allows reversible motor operation.
Forcible-terminal operation function
Torque control function
Cumulative power monitoring function
Servo on function
forcing function
Easy sequence function (*1)
Analog command holding function
Absolute position control mode
Intelligent pulse counter
Easy sequence function (*1)
Function code
C011 to C018
C019
A019
A020/A220/
0.00 or "start frequency" to
A320
"maximum frequency" (Hz)
A021 to A035
Reference item
C011 to C018: Terminal [1] to [8] active state
C019: Terminal [FW] active state
Data
00 a-contact (NO)
01 b-contact (NC)
00 a-contact (NO)
01 b-contact (NC)
A019: Multispeed operation selection
A020/A220/A320: Multispeed frequency setting,
A021 to A035: Multispeed 1 to 15 settings
C001 to C008: Terminal [1] to [8] functions
C169: Multistage speed/position determination
Data
00 Binary operation mode with up to 16 speeds
01 Bit operation mode with up to 8 speeds
Setting of the frequency as each speed
4-47
Explanation of Functions
Availability(Yes or No)
CT mode VT mode
Y
Y N
Y
Y N
Y N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y N
Y N
Y N
Y N
Y N
Y N
Y N
Y N
Y
Y
Y
Y
Related code
Description
Related code
1st/2nd/3rd motors
time
Description
Page
Y 4-52
4-99
4-4
Y
4-112
4-92
Y
Y
Y
Y
-
Y
Y
Y
Y
Y 4-60
4-109
4-110
4-111
4-109
Y
4-60
Y
-
Y
Y