Hitachi SJ700D-004L Instruction Manual page 189

Chapter 4
(iii) 02, 12 command: This command turns the specified intelligent input terminals on or off.
- Transmission frame
Frame format
STX Station No.
STX Control code (Start of TeXt)
Station number of control-target
Station No.
inverter
Command Command to be transmitted
Data Data to be transmitted
BCC Block check code
CR Control code (Carriage Return)
Note 5: The table below lists the functions of the intelligent input terminals and corresponding hexadecimal data. (For
details, see the explanation of the intelligent input terminal functions.)
Data (hexadecimal)
0000000000000001 FW: Forward rotation
0000000000000002 RV: Reverse rotation
0000000000000004 CF1: Multispeed 1 setting
0000000000000008 CF2: Multispeed 2 setting
0000000000000010 CF3: Multispeed 3 setting
0000000000000020 CF4: Multispeed 4 setting
0000000000000040 JG: Jogging
0000000000000080 DB: External DC braking
0000000000000100 SET: Set 2nd motor data
0000000000000200 2CH: 2-stage acceleration/deceleration
0000000000000400 -
0000000000000800 FRS: Free-run stop
0000000000001000 EXT: External trip
0000000000002000 USP: Unattended start protection
0000000000004000 CS: Commercial power source enable
0000000000008000 SFT: Software lock
0000000000010000 AT: Analog input voltage/current select
0000000000020000 SET3: 3rd motor control
0000000000040000 RS: Reset
0000000000080000 -
0000000000100000 STA: Starting by 3-wire input
0000000000200000 STP: Stopping by 3-wire input
0000000000400000
F/R: Forward/reverse switching by 3-wire input
0000000000800000 PID: Enabling/disabling PID
0000000001000000 PIDC: PID reset
0000000002000000 -
0000000004000000 CAS: Control gain setting
0000000008000000 UP: Remote control UP function
0000000010000000 DWN: Remote control DOWN function
0000000020000000 DWN: Remote control data clearing
0000000040000000 -
0000000080000000 OPE: Forcible operation
Command Data
Description
Description
Explanation of Functions
BCC CR
Data size
1 byte STX (0x02)
2 bytes 01 to 32, or FF (broadcast to all stations)
2 bytes 02
16 bytes See Note 5.
XOR of the items from "Station No." to "Data." See
2 bytes
Item (3) of this section.
1 byte CR (0x0D)
Data (hexadecimal)
0000000100000000 SF1: Multispeed bit 1
0000000200000000 SF2: Multispeed bit 2
0000000400000000 SF3: Multispeed bit 3
0000000800000000 SF4: Multispeed bit 4
0000001000000000 SF5: Multispeed bit 5
0000002000000000 SF6: Multispeed bit 6
0000004000000000 SF7: Multispeed bit 7
0000008000000000 OLR: Overload restriction selection
0000010000000000 TL: Enabling /disabling torque limitation
0000020000000000 TRQ1: Torque limit selection bit 1
0000040000000000 TRQ2: Torque limit selection bit 2
0000080000000000 PPI: P/PI mode selection
0000100000000000 BOK: Braking confirmation
0000200000000000 ORT: Orientation
0000400000000000 LAC: LAD cancellation
0000800000000000 PCLR: Clearance of position deviation
0001000000000000
STAT: Pulse train position command input enable
0002000000000000 -
0004000000000000 ADD: Trigger for frequency addition
0008000000000000 F-TM: Forcible-terminal operation
0010000000000000 ATR: Permission of torque command input
0020000000000000 KHC: Cumulative power clearance
0040000000000000 SON: Servo On
0080000000000000 FOC: Forcing
0100000000000000 MI1: General-purpose input 1
0200000000000000 MI2: General-purpose input 2
0400000000000000 MI3: General-purpose input 3
0800000000000000 MI4: General-purpose input 4
1000000000000000 MI5: General-purpose input 5
2000000000000000 MI6: General-purpose input 6
4000000000000000 MI7: General-purpose input 7
8000000000000000 MI8: General-purpose input 8
4-118
Setting
Description