HEIDENHAIN TNC 620 User Manual page 496

Index
Index
3
3D Touch Probes...................... 298
3-D touch probes....................... 46
A
Automatic datum setting.......... 330
At center of 4 holes............... 372
Center of a bolt hole circle..... 366
Center of a circular pocket
(hole)...................................... 348
Center of a circular stud......... 353
Center of a rectangular
pocket.................................... 341
Center of a rectangular stud... 345
In any axis.............................. 376
Inside of corner...................... 362
In the touch probe axis........... 370
Outside of corner................... 357
Ridge center.......................... 338
Slot center............................. 334
Automatic tool measurement... 480
Axis-specific scaling................. 267
B
Back boring................................ 83
Basic rotation
Measure during program run.. 308
Bolt hole circle......................... 179
Bore milling................................ 90
Boring......................................... 77
C
Centering................................... 71
Circular pocket
Roughing+finishing................ 141
Circular point patterns.............. 179
Circular slot
Roughing+finishing................ 150
Circular stud..................... 159, 163
Classification of results............ 387
Compensating workpiece
misalignment............................ 308
By measuring two points on a
straight line............................ 310
Over two circular studs.......... 316
Over two holes...................... 313
Via rotary axis................ 319, 323
Confidence interval.................. 303
Consideration of basic rotation. 298
Contour cycles......................... 188
Contour train.................... 208, 210
Coordinate transformation........ 254
Cycle.......................................... 50
Calling...................................... 52
Define...................................... 51
Cycles and point tables.............. 67
496
Cylinder surface
Machine contour............ 223, 232
Ridge machining..................... 229
Slot machining........................ 226
D
Datum shift.............................. 255
In the program....................... 255
With datum tables................. 256
Drilling............................ 73, 80, 86
Drilling Cycles............................ 70
Dwell time................................ 279
E
Engraving................................. 286
F
Face milling.............................. 290
FCL function................................ 9
Feature Content Level.................. 9
Floor finishing........................... 203
Fundamentals of Thread
Milling...................................... 111
H
Helical thread drilling/milling..... 124
I
Inside thread milling................. 113
K
Kinematic measurement
Accuracy................................. 455
Backlash................................. 457
Calibration methods.... 456, 469,
471
Hirth coupling......................... 453
Logging function..... 448, 463, 473
Measuring point selection.... 449,
454
Measuring position selection. 455
Prerequisites.......................... 446
Kinematics measurement........ 444
Kinematics Measurement
Measure kinematics....... 450, 464
Kinematics measurement
Save kinematics..................... 447
KinematicsOpt.......................... 444
L
Linear point patterns................ 182
M
Machine parameters for 3D touch
probe........................................ 301
Machining pattern...................... 58
Measure angle......................... 392
Measure angle of a plane......... 421
Measure any coordinate........... 415
Measure bolt hole circle........... 418
HEIDENHAIN | TNC 620 | User's manual for cycle programming | 9/2015
Measure hole........................... 395
Measure hole inside................. 395
Measure hole outside.............. 399
Measure kinematics................. 450
Preset compensation............. 464
Measurement parameters........ 387
Measurement results in Q
parameters............................... 387
Measure rectangular pocket..... 406
Measure rectangular stud........ 403
Measure the plane angle.......... 421
Measure the slot width............ 409
Measure the width of a
ridge................................. 412, 412
Measuring slot width............... 409
Measuring the width of a ridge 412
Mirroring................................... 262
Multiple measurements........... 303
O
Outside thread milling.............. 128
P
Pattern definition........................ 58
Peck drilling.......................... 86, 93
Point patterns........................... 178
Overview................................ 178
Point tables................................ 65
Positioning logic....................... 304
Probing feed rate..................... 302
Program call............................. 280
Via cycle................................. 280
R
Reaming..................................... 75
Recording measurement results....
385
Rectangular pocket
Roughing+finishing................ 137
Rectangular stud...................... 155
Rotation.................................... 264
Roughing:See SL Cycles,
Roughing.................................. 199
S
Scaling...................................... 266
Set a basic rotation.................. 322
Side finishing............................ 205
Single-lip deep-hole drilling......... 93
SL Cycles................. 188, 223, 232
Contour cycle......................... 190
Contour data.......................... 195
Contour train.................. 208, 210
Floor finishing......................... 203
SL cycles
Fundamentals......................... 188
Fundamentals......................... 250
SL Cycles
Pilot drilling............................ 197