Menu 17: Motion Processors; Table 11-6 Digitax St Indexer - Emerson Digitax ST User Manual

Safety Product Mechanical
Information information installation
11.16

Menu 17: Motion processors

Menu 17 parameter functions are dependant on the Digitax ST variant.
11.16.1 Digitax ST Base
Menu 17 not available.
11.16.2 Digitax ST Indexer

Table 11-6 Digitax ST Indexer

Parameter
17.01 Motion processor ID
17.02 Motion processor software version
17.03 DPL program status
17.04 Available system resource
17.10 DPL Print Routing
17.11 Clock tick time (ms)
17.12 Motion engine sample rate
17.13 Enable autorun
17.14 Global run time trip enable
17.15 Disable reset on trip cleared
17.16 Encoder data update rate
17.17 Enable parameter over range trips
17.18 Watchdog enable
17.19 Save request
17.20 Enable power down save
Enable menu 20 save and
17.21
restore
17.37 Reject download if drive enabled
17.38 Do not trip drive on APC run-time error
17.39 Inter-UT70 synchronization status
17.40 Inter-UT70 master transfer mode
17.41 Indexer control
17.42 Freeze main drive position
17.43 Freeze invert
17.44 Task priority level
17.45 User set-up parameter 1
17.46 User set-up parameter 2
17.47 User set-up parameter 3
17.48 DPL line number in error
17.49 User program ID
17.50 Motion processor error status*
17.51 Motion processor software sub-version
RW Read / Write RO Read only
FI Filtered DE Destination
*See trip SLX.Er, Automation (I/O Expansion) module category on page 192.
Digitax ST User Guide
Issue Number: 3
Electrical Getting Basic
installation started parameters
Range( )
0 to 599
0.00 to 99.99
None (0), Stop (1), Run (2), Trip (3)
0 to 100
SYPT: OFF (0), RS485: On (1)
0 to 200
dISAbLEd (0), 0.25 ms (1), 0.5 ms (2), 1 ms (3),
2 ms (4), 4 ms (5), 8 ms (6)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
0 to 3
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
0 to 3
0 to 10
0 to 3
OFF (0) or On (1)
OFF (0) or On (1)
0 to 255
0 to 2,147,483,647
-32,767 to +32,768
0 to 255
0 to 99
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
Running the SMARTCARD
Optimization
motor Operation
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced
Technical
Diagnostics
PLC parameters
Data
Default( )
RO Uni
RO Uni
RO Txt
RO Uni
SYPT: OFF (0) RW Bit
10 RW Uni
dISAbLEd (0) RW Txt
On (1) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
0 RW Uni
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
0 RO Uni
1 RW Uni
0 RW Uni
OFF (0) RW Bit
OFF (0) RW Bit
0 RW Uni
0 RO Uni
0 RO Uni
0 RO Uni
0 RO Uni
0 RO
RO Uni
RO Uni
Txt Text string
US User save PS
UL listing
information
Type
PT US
NC PT
NC PT
NC PT
US
US
US
US
US
US
US
US
US
NC
US
US
US
US
NC
US
NC
US
US
US
NC PT
NC PT
NC PT
NC PT
Bi NC PT
NC PT
NC PT
Power down save
159