Emerson Digitax ST User Manual page 130

Safety Product Mechanical
Information information installation
SM-Universal Encoder Plus parameters
Parameter
x.01 Solutions Module ID
x.02 Solutions Module software version
x.03 Speed
x.04 Revolution counter
x.05 Position
x.06 Fine position
x.07 Marker position reset disable
x.08 Marker flag
Encoder turns/ linear encoder comms
x.09
to sine wave ratio
x.10 Equivalent lines per revolution
Single turn comms bits/ linear encoder
x.11
comms bits
x.12 Motor thermistor check enable
x.13 Encoder supply voltage
x.14 Encoder comms baud rate
x.15 Encoder type
Rotary encoder select/ comms only
x.16
encoder mode/ terminations
x.17 Error detection level
Auto configuration/ SSI binary format
x.18
select
x.19 Feedback filter
x.20 Maximum feedback reference
Feedback reference/ motor thermistor
x.21
resistance
x.22 Feedback reference scaling
x.23 Feedback reference destination
x.24 Encoder simulation source
x.25 Encoder simulation ratio numerator
x.26 Encoder simulation ratio denominator
x.27 Encoder simulation resolution select
x.28 Encoder simulation mode
x.29 Non-marker reset revolution counter
x.30 Non-marker reset position
x.31 Non-marker reset fine position
x.32 Marker revolution counter
x.33 Marker position
x.34 Marker fine position
x.35 Freeze revolution counter
x.36 Freeze position
x.37 Freeze fine position
x.38 Freeze input mode selection
x.39 Freeze flag
x.40 Pass freeze to drive and other slots
x.41 Freeze invert
Encoder comms transmit register/ Sin
x.42
signal value
Encoder comms receive register/ Cos
x.43
signal value
x.44 Disable encoder position check
x.45 Position feedback initialised
x.46 Lines per revolution divider
x.47 SSI output turns
x.48 SSI output comms resolution
x.49 Lock position feedback
x.50 Solutions Module error status*
x.51 Solutions Module software sub-version
RW Read / Write RO Read only
FI Filtered DE Destination
*See trip SLX.Er, .Feedback module category on page 189
130
Electrical Getting Basic
installation started parameters
Range( )
0 to 599
0.00 to 99.99
±40,000.0 rpm
0 to 65,535 revolutions
16
0 to 65,535 (1/2 ths of a revolution)
32
0 to 65,535 (1/2 nds of a revolution)
OFF (0) or On (1)
OFF (0) or On (1)
0 to 16 bits
0 to 50,000
0 to 32 bits
OFF (0) or On (1)
5V (0), 8V (1), 15V (2)
100 (0), 200 (1), 300 (2), 400 (3), 500 (4),
1,000 (5), 1,500 (6), 2,000 (7)
Ab (0), Fd (1), Fr (2), Ab.SErVO (3),
Fd.SErVO (4), Fr.SErVO (5), SC (6),
SC.HiPEr (7), EndAt (8), SC.EndAt (9),
SSI (10), SC.SSI (11), SC.UVW (12)
0 to 2
0 to 7
OFF (0) or On (1)
0.0 to 40,000.0 rpm
±100.0 %
0.000 to 4.000
Pr 0.00 to Pr 21.51
Pr 0.00 to Pr 21.51
0.0000 to 3.0000
0.0000 to 3.0000
OFF (0) or On (1)
Ab (0), Fd (1), SSI.Gray (2), SSI.Bin (3),
Ab.L (4), Fd.L (5), H-drv (6), H-int (7)
0 to 65,535 revolutions
16
0 to 65,535 (1/2 ths of a revolution)
32
0 to 65,535 (1/2 nds of a revolution)
0 to 65,535 revolutions
16
0 to 65,535 (1/2 ths of a revolution)
32
0 to 65,535 (1/2 nds of a revolution)
0 to 65,535 revolutions
16
0 to 65,535 (1/2 ths of a revolution)
32
0 to 65,535 (1/2 nds of a revolution)
Bit 0 (LSB) = 24V input
Bit 1 = EIA485 input
Bit 2 (MSB) = From another Solutions Module
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
0 to 65,535
0 to 65,535
OFF (0) or On (1)
OFF (0) or On (1)
1 to 1024
0 to 16 bits
0 to 32 bits
OFF (0) or On (1)
0 to 255
0 to 99
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
Running the SMARTCARD
Optimization
motor Operation
0 to 5 (0 to 16 ms)
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced
Technical
Diagnostics
PLC parameters
Data
Default( )
102 RO Uni
RO Uni
RO
RO Uni FI NC PT
RO Uni FI NC PT
RO Uni FI NC PT
OFF (0) RW Bit
OFF (0) RW Bit
16 RW Uni
4096 RW Uni
0 RW Uni
OFF (0) RW Bit
5V (0) RW Uni
300 (2) RW Txt
Ab (0) RW Uni
1 RW Uni
1 RW Uni
OFF (0) RW Bit
0 RW Uni
1500.0 RW Uni
RO
1.000 RW Uni
Pr 0.00 RW Uni DE
Pr 0.00 RW Uni
0.2500 RW Uni
1.0000 RW Uni
OFF (0) RW Bit
Ab (0) RW Txt
RO Uni
RO Uni
RO Uni
RO Uni
RO Uni
RO Uni
RO Uni
RO Uni
RO Uni
1 RW Uni
OFF (0) RW Bit
OFF (0) RW Bit
OFF (0) RW Bit
0 RW Uni
0 RW Uni
OFF (0) RW Bit
RO Bit
1 RW Uni
16 RW Uni
0 RW Uni
OFF (0) RW Bit
RO Uni
RO Uni
Txt Text string
US User save PS
Digitax ST User Guide
UL listing
information
Type
PT US
NC PT
Bi FI NC PT
US
NC
US
US
US
US
US
US
US
US
US
US
US
US
Bi NC PT
US
PT US
PT US
US
US
NC
US
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
US
NC
NC US
US
NC
NC
NC
NC PT
US
US
US
NC PT
NC PT
Power down save
Issue Number: 3