Emerson Digitax ST User Manual page 119

Safety Product Mechanical
Information information installation
Parameter
12.01 Threshold detector 1 output
12.02 Threshold detector 2 output
12.03 Threshold detector 1 source
12.04 Threshold detector 1 level
Threshold detector 1
12.05
hysteresis
Threshold detector 1 output
12.06
invert
Threshold detector 1
12.07
destination
12.08 Variable selector 1 source 1
12.09 Variable selector 1 source 2
12.10 Variable selector 1 mode
Variable selector 1
12.11
destination
12.12 Variable selector 1 output
Variable selector 1 source 1
12.13
scaling
Variable selector 1 source 2
12.14
scaling
12.15 Variable selector 1 control
12.23 Threshold detector 2 source
12.24 Threshold detector 2 level
Threshold detector 2
12.25
hysteresis
Threshold detector 2 output
12.26
invert
Threshold detector 2
12.27
destination
12.28 Variable selector 2 source 1
12.29 Variable selector 2 source 2
12.30 Variable selector 2 mode
Variable selector 2
12.31
destination
12.32 Variable selector 2 output
Variable selector 2 source 1
12.33
scaling
Variable selector 2 source 2
12.34
scaling
12.35 Variable selector 2 control
The brake control functions are provided to allow well co-ordinated operation of an external brake with the drive. While both hardware
and software are designed to high standards of quality and robustness, they are not intended for use as safety functions, i.e. where a
fault or failure would result in a risk of injury. In any application where the incorrect operation of the brake release mechanism could
result in injury, independent protection devices of proven integrity must also be incorporated.
WARNING
12.40 Brake release indicator
12.41 Brake controller enable
12.43 Lower current threshold
12.45 Brake apply frequency / speed
12.46 Brake apply speed delay
12.47 Post brake release delay
12.48 Brake apply delay
Enable position controller
12.49
during brake release
RW Read / Write RO Read only
FI Filtered DE Destination
Digitax ST User Guide
Issue Number: 3
Electrical Getting Basic
installation started parameters
Range( )
OFF (0) or On (1)
OFF (0) or On (1)
Pr 0.00 to 21.51
0.00 to 100.00 %
0.00 to 25.00 %
OFF (0) or On (1)
Pr 0.00 to 21.51
Pr 0.00 to 21.51
Pr 0.00 to 21.51
Select input 1 (0), select input 2 (1), add (2),
subtract (3), multiply (4), divide (5),
filter (6), linear ramp (7), absolute value (8),
powers (9), sectional control (10),
external rectifier monitor (11)
Pr 0.00 to 21.51
±100.00 %
±4.000
±4.000
0.00 to 100.00 s
Pr 0.00 to 21.51
0.00 to 100.00 %
0.00 to 25.00 %
OFF (0) or On (1)
Pr 0.00 to 21.51
Pr 0.00 to 21.51
Pr 0.00 to 21.51
Select input 1 (0), select input 2 (1), add (2),
subtract (3), multiply (4), divide (5),
filter (6), linear ramp (7), absolute value (8),
powers (9), sectional control (10),
external rectifier monitor (11)
Pr 0.00 to 21.51
±100.00 %
±4.000
±4.000
0.00 to 100.00 s
OFF (0) or On (1)
dis (0), rEL (1), d IO (2), USEr (3)
0 to 200 %
0 to 200 rpm
0.0 to 25.0 s
0.0 to 25.0 s
0.0 to 25.0 s
OFF (0) or On (1)
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
Running the SMARTCARD
Optimization
motor Operation
1.0
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced
Technical
PLC parameters
Data
Default( )
RO Bit
RO Bit
Pr 0.00 RW Uni
0.00 RW Uni
0.00 RW Uni
OFF (0) RW Bit
Pr 0.00 RW Uni DE
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Select input 1 (0) RW Uni
Pr 0.00 RW Uni DE
RO
1.000 RW Bi
1.000 RW Bi
0.00 RW Uni
Pr 0.00 RW Uni
0.00 RW Uni
0.00 RW Uni
OFF (0) RW Bit
Pr 0.00 RW Uni DE
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Select input 1 (0) RW Uni
Pr 0.00 RW Uni DE
RO
1.000 RW Bi
1.000 RW Bi
0.00 RW Uni
RO Bit
dis (0) RW Txt
10 RW Uni
5 RW Bit
RW Uni
1.0 RW Uni
1.0 RW Uni
OFF (0) RW Bit
Txt Text string
US User save PS
UL listing
Diagnostics
information
Type
NC PT
NC PT
PT US
US
US
US
PT US
PT US
PT US
US
PT US
Bi NC PT
US
US
US
PT US
US
US
US
PT US
PT US
PT US
US
PT US
Bi NC PT
US
US
US
NC PT
US
US
US
US
US
US
US
Power down save
119