Emerson Digitax ST User Manual page 201

Table 2-1 Maximum ratings ................................................8
Table 2-2 Solutions Module identification .........................11
Table 2-3 Keypad identification .........................................13
Table 2-4 Other options ....................................................14
Table 3-1 External EMC filter ratings ................................18
Table 3-2 Torque settings .................................................19
Table 3-3 Plug-in terminal block maximum cable sizes ....19
Table 4-1 Supply requirements .........................................22
Table 4-2 Behavior of the drive in the event of a
motor circuit ground (earth) fault with an
IT supply ...........................................................22
Table 4-3 DC bus data ......................................................23
Table 4-4 Low voltage DC levels ......................................23
Table 4-5 High voltage DC levels .....................................23
Table 4-6 Control supply voltage levels ............................23
Table 4-7 Fuse ratings and cable sizes ............................24
Table 4-8 Maximum AC input fusing .................................24
Table 4-9 Motor cable size and maximum lengths ...........25
Table 4-10 Internal braking resistor data ............................26
Table 4-11 Minimum resistance and power ratings ............26
Table 4-12 Ground leakage current with internal
EMC filter installed ............................................26
Table 4-13 Immunity compliance ........................................29
Table 4-14 DST120X (200V) emission compliance
(single and three phase drives ..........................30
Table 4-15 DST140X (400V) emission compliance ............30
Table 4-16 Connection details for RJ45 connector .............31
Table 4-17 Isolated serial comms lead details ....................31
Table 4-18 The control connections consist of: ..................31
Table 4-20 Encoder types ...................................................37
Table 4-21 Feedback resolution based on frequency
and voltage level ...............................................39
Table 4-22 Encoder output types ........................................39
Table 4-23 Buffered encoder connections ..........................39
Table 4-24 Digitax ST Plus connector details .....................40
Table 4-26 Digitax EZMotion connector details ..................40
Table 5-1 User interface compatibility ...............................42
Table 7-1 Minimum control connection requirements
for each control mode .......................................58
Table 7-2 Minimum control connection requirements .......58
Table 7-3 Parameters required for feedback device
set-up ................................................................63
Table 7-4 Restrictions of drive encoder lines per
revolution with software version
V01.06.01 and later ..........................................65
Table 7-5 Buffered encoder output type ...........................66
Table 9-1 SMARTCARD data blocks ................................71
Table 9-2 SMARTCARD codes ........................................71
Table 9-3 Key to parameter table coding ..........................73
Table 9-4 Trip conditions ..................................................75
Table 9-5 SMARTCARD status indications ......................76
Table 11-1 Menu descriptions .............................................79
Table 11-2 Key to parameter table coding ..........................79
Table 11-3 Feature look-up table ........................................80
Table 11-4 Definition of parameter ranges & variable
maximums ........................................................82
Table 11-5 Defaults for Pr 10.30 and Pr 10.31 .................113
Table 11-6 Digitax ST Indexer ..........................................159
Table 11-7 Digitax ST Plus ...............................................160
Table 11-8 Digitax ST EZMotion .......................................161
Table 11-9 Active reference ..............................................164
Digitax ST User Guide
Issue Number: 3
List of tables
Table 12-1
Table 12-2
Table 12-3
Table 12-4
Table 12-5
Table 12-6
Table 12-7
Table 12-8
Table 12-9
Table 12-10 Continuous rating with no overload, ≤240Vac
Table 12-11 Maximum rectifier power, ≤230Vac supply for
Table 12-12 Maximum rectifier power, ≤240Vac supply
Table 12-13 Maximum drive losses ................................... 175
Table 12-14 Supply requirements ...................................... 175
Table 12-15 IP Rating degrees of protection ..................... 176
Table 12-16 UL enclosure ratings ...................................... 176
Table 12-17 Overall drive dimensions ................................ 177
Table 12-18 Supply fault current used to calculate
Table 12-19 Fuse ratings and cable sizes ......................... 177
Table 12-20 Maximum AC input fusing .............................. 178
Table 12-21 Motor cable size and maximum lengths ......... 178
Table 12-22 Minimum resistance and power ratings ......... 178
Table 12-23 Torque settings .............................................. 179
Table 12-24 Plug-in terminal block maximum cable sizes . 179
Table 12-25 Immunity compliance ..................................... 179
Table 12-26 DST120X (200V) emission compliance
Table 12-27 DST140X (400V) emission compliance ......... 179
Table 12-28 External EMC filter ratings ............................. 180
www.controltechniques.com
Repetitive profile with defined level of Ipeak
at 6kHz switching frequency, ≤230Vac
supply for DST120X and ≤400Vac supply
for DST140X .................................................. 171
Repetitive profile with defined level of Ipeak
at 8kHz switching frequency, ≤230Vac
supply for DST120X and ≤400Vac supply
for DST140X .................................................. 172
Repetitive profile with defined level of Ipeak
at 6kHz switching frequency, ≤240Vac
supply for DST120X and ≤480Vac
supply for DST140X ....................................... 172
Repetitive profile with defined level of Ipeak
at 8kHz switching frequency, ≤240Vac supply
for DST120X and ≤480Vac supply
for DST140X .................................................. 172
Repetitive profile with defined ratio between
Ibase to Ipeak at 6kHz switching frequency,
≤230Vac supply for DST120X and
≤400Vac supply for DST140X ........................ 173
Repetitive profile with defined ratio between
Ibase to Ipeak at 8kHz switching frequency,
≤230Vac supply for DST120X and
≤400Vac supply for DST140X ........................ 173
Repetitive profile with defined ratio between
Ibase to Ipeak at 6kHz switching frequency,
≤240Vac supply for DST120X and ≤480Vac
supply for DST140X ....................................... 174
Repetitive profile with defined ratio between
Ibase to Ipeak at 8kHz switching frequency,
≤240Vac supply for DST120X and
≤480Vac supply for DST140X ........................ 174
Continuous rating with no overload, ≤230Vac
supply for DST120X and ≤400Vac
supply for DST140X ....................................... 174
supply for DST120X and ≤480Vac
supply for DST140X ....................................... 174
DST120X and ≤400Vac supply
for DST140X .................................................. 175
for DST120X and ≤480Vac supply
for DST140X .................................................. 175
maximum input currents ................................. 177
(single and three phase drives ....................... 179
201