Menu 11: General Drive Set-Up - Emerson Digitax ST User Manual

Safety Product Mechanical
Information information installation
11.11

Menu 11: General drive set-up

Parameter
11.01 Parameter 0.11 set up
11.02 Parameter 0.12 set up
11.03 Parameter 0.13 set up
11.04 Parameter 0.14 set up
11.05 Parameter 0.15 set up
11.06 Parameter 0.16 set up
11.07 Parameter 0.17 set up
11.08 Parameter 0.18 set up
11.09 Parameter 0.19 set up
11.10 Parameter 0.20 set up
11.11 Parameter 0.21 set up
11.12 Parameter 0.22 set up
11.13 Parameter 0.23 set up
11.14 Parameter 0.24 set up
11.15 Parameter 0.25 set up
11.16 Parameter 0.26 set up
11.17 Parameter 0.27 set up
11.18 Parameter 0.28 set up
11.19 Parameter 0.29 set up
11.20 Parameter 0.30 set up
11.21 Parameter scaling
11.22 Parameter displayed at power-up
11.23 Serial address
11.24 Serial mode
11.25 Baud rate
11.26 Minimum comms transmit delay
11.28 Drive derivative
11.29 Software version
11.30 User security code
11.32 Maximum current rating
11.33 Drive voltage rating
11.34 Software sub-version
11.35 Number of modules
SMARTCARD parameter
11.36
data previously loaded
11.37 SMARTCARD data number
11.38 SMARTCARD data type / mode
11.39 SMARTCARD data version
11.40 SMARTCARD data checksum
11.41 Status mode timeout
11.42 Parameter copying
11.43 Load defaults
11.44 Security status
11.45 Select motor 2 parameters
11.46 Defaults previously loaded
11.47 Drive Onboard PLC program enable
11.48 Drive Onboard PLC program status
Drive Onboard PLC programming
11.49
events
Drive Onboard PLC program average
11.50
scan time
11.51 Drive Onboard PLC program first run
Drive serial number least significant 9
11.52
digits
Drive serial number most significant
11.53
digits
* Modes 1 and 2 are not user saved, Modes 0, 3 and 4 are user saved
RW Read / Write RO Read only
FI Filtered DE Destination
114
Electrical Getting Basic
installation started parameters
Range( )
Pr 1.00 to Pr 21.51
0.000 to 9.999
Pr 0.00 to 00.50
{0.37} 0 to 247
{0.35} AnSI (0), rtU (1), Lcd (2)
300 (0), 600 (1), 1200 (2), 2400 (3), 4800 (4),
{0.36} 9600 (5), 19200 (6), 38400 (7),
57600 (8)*, 115200 (9)* *Modbus RTU only
0 to 250ms
0 to 16
{0.50} 1.00 to 99.99
{0.34} 0 to 999
{0.32} 0.00 to 9999.99A
{0.31} 200 (0), 400 (1), 575 (2), 690 (3)
0 to 99
0 to 10
{0.29} 0 to 999
0 to 1003
0 to 18
0 to 9,999
0 to 65,335
0 to 250s
nonE (0), rEAd (1), Prog (2), AutO (3),
{0.30}
boot (4)
nonE (0), Eur (1), USA (2)
{0.49} L1 (0), L2 (1), Loc (2)
OFF (0) or On (1)
0 to 2000
Halt program (0)
Run program: out of range = clip (1)
Run program: out of range = trip (2)
-128 to +127
0 to 65,535
0 to 65,535 ms
OFF (0) or On (1)
0 to 999999999
0 to 65535
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
Running the SMARTCARD
Optimization
motor Operation
Run program: out of range = trip (2)
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced
Technical
Diagnostics
PLC parameters
Data
Default( )
Pr 3.29 RW Uni
Pr 4.01 RW Uni
Pr 7.07 RW Uni
Pr 4.11 RW Uni
Pr 2.04 RW Uni
Pr 2.02 RW Uni
Pr 4.12 RW Uni
Pr 8.29 RW Uni
Pr 7.11 RW Uni
Pr 7.14 RW Uni
Pr 7.15 RW Uni
Pr 1.10 RW Uni
Pr 1.05 RW Uni
Pr 1.21 RW Uni
Pr 1.22 RW Uni
Pr 3.08 RW Uni
Pr 3.34 RW Uni
Pr 6.13 RW Uni
Pr 11.36 RW Uni
Pr 11.42 RW Uni
1.000 RW Uni
Pr 0.10 RW Uni
1 RW Uni
rtU (1) RW Txt
19200 (6) RW Txt
2 RW Uni
RO Uni
RO Uni
0 RW Uni
RO Uni
RO Txt
RO Uni
0 RW Uni
0 RO Uni
0 RW Uni
RO Txt
0 RW Uni
RO Uni
240 RW Uni
nonE (0) RW Txt
nonE (0) RW Txt
RW Txt
OFF (0) RW Bit
RO Uni
RW Uni
RO
RO Uni
RO Uni
RO Bit
RO Uni
RO Uni
Txt Text string
US User save PS
Digitax ST User Guide
UL listing
information
Type
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
US
PT US
US
PT US
US
US
NC PT
NC PT
NC PT PS
NC PT
NC PT
NC PT
PT US
NC PT US
NC
NC PT
NC
NC PT
US
NC *
NC
PT US
US
NC PT US
US
Bi NC PT
NC PT PS
NC PT
NC PT
NC PT
NC PT
Power down save
Issue Number: 3