Kyocera Mita FS-1050 Operation Manual page 148

Printed Results Printed Results
Printed Results Printed Results
Faint or blurred printing
Grey background.
Dirt on the top edge or back of the paper
Corrective Measures Corrective Measures
Corrective Measures Corrective Measures
Check the EcoPrint setting. Check the EcoPrint setting. Check the EcoPrint setting. Check the EcoPrint setting.
If EcoPrint is On, switch it Off from the operator panel.
EcoPrint EcoPrint EcoPrint EcoPrint
(See on page
Check the operator panel. Check the operator panel.
Check the operator panel. Check the operator panel.
• If the Toner low TK-17 message appears and the
ATTENTION indicator flashes, install a new toner kit.
3.1.1 Toner Container Replacement 3.1.1 Toner Container Replacement
See section 3.1.1 Toner Container Replacement 3.1.1 Toner Container Replacement
Interval Interval Interval Interval 3-2 3-2 3-2 3-2
on page
• Set the print density to a darker level. See
the Print Density the Print Density the Print Density the Print Density
on page
Clean the charger wire. Clean the charger wire.
Clean the charger wire. Clean the charger wire.
Open the top and front covers of the printer. Remove the
process unit form the printer and slide the charger
cleaner knob back and forth a few times. See section
Cleaning Cleaning Cleaning Cleaning 3-6 3-6 3-6 3-6
on page
Set the paper type to Thin. Set the paper type to Thin.
Set the paper type to Thin. Set the paper type to Thin.
From the operation panel, select Thin as the paper type.
Selecting the Paper Source Selecting the Paper Source
See Selecting the Paper Source Selecting the Paper Source
Check the operator panel. Check the operator panel. Check the operator panel. Check the operator panel.
If the Toner low TK-17 message appears and the
ATTENTION indicator flashes, install a new toner kit. See
section 3.1 Toner Container Replacement 3.1 Toner Container Replacement 3.1 Toner Container Replacement 3.1 Toner Container Replacement
Check the print density. Check the print density. Check the print density. Check the print density.
Select a lighter print density setting. See
Print Density Print Density Print Density Print Density
on page
Clean the charger wire. Clean the charger wire.
Clean the charger wire. Clean the charger wire.
Open the top and front covers of the printer. Remove the
process unit form the printer and slide the charger
cleaner knob back and forth a few times. See section
Cleaning Cleaning 3-6 3-6
Cleaning Cleaning on page 3-6 3-6
Check the process unit. Check the process unit.
Check the process unit. Check the process unit.
Open the top and front covers of the printer and check
that the process unit is correctly installed and seated as
far as it can go.
Check the transfer roller. Check the transfer roller. Check the transfer roller. Check the transfer roller.
Open the top and front covers of the printer. Remove the
process unit from the printer and make sure that the
transfer roller is clean. If it is not, print several pages
until the problem disappears.
Check the registration roller. Check the registration roller. Check the registration roller. Check the registration roller.
Open the top and front covers of the printer. Remove the
process unit from the printer and make sure that the
registration roller is clean. If it is not, wipe it with the
provided wiper cloth.
4-4
Print Quality Problems
1-46 1-46 1-46 1-46
)
.
1-71 1-71 1-71 1-71
.
.
1-66 1-66
on page 1-66 1-66 .
on page
Adjusting the Adjusting the Adjusting the Adjusting the
1-71 1-71 1-71 1-71
.
.
(Continued on next page)
Adjusting Adjusting Adjusting Adjusting
3.2 3.2
3.2 3.2
3-2 3-2 3-2 3-2 .
3.2 3.2
3.2 3.2