Mitsubishi FX3G SERIES User Manual page 366

FX Series Programmable Controllers
3G
User's Manual - Hardware Edition
Number and
name
Positioning
[D]8329 to [D]8339 Not used
D 8340 Lower
D 8341 Upper
D 8342 [Y000] Bias speed Default: 0
D 8343 Lower
D 8344 Upper
[Y000] Creep speed
D 8345
Default: 1000
D 8346 Lower
D 8347 Upper
[Y000] Acceleration time
D 8348
Default: 100
[Y000] Deceleration time
D 8349
Default: 100
D 8350 Lower
D 8351 Upper
D 8352 [Y001] Bias speed Default: 0
D 8353 Lower
D 8354 Upper
[Y001] Creep speed
D 8355
Default: 1000
D 8356 Lower
D 8357 Upper
[Y001] Acceleration time
D 8358
Default: 100
[Y001] Deceleration time
D 8359
Default: 100
D 8360 Lower
D 8361 Upper
D 8362 [Y002] Bias speed Default: 0
D 8363 Lower
D 8364 Upper
[Y002] Creep speed
D 8365
Default: 1000
D 8366 Lower
D 8367 Upper
[Y002] Acceleration time
D 8368
Default: 100
[Y002] Deceleration time
D 8369
Default: 100
RS2 (FNC 87) [ch0]
RS2 (FNC 87) [ch0]
D 8370
Communication format setting
[D]8371 Not used
RS2 (FNC 87) [ch0]
*1
[D]8372
Remaining points of transmit data
RS2 (FNC 87) [ch0]
*1
[D]8373
Monitoring receive data points
[D]8374 Not used
[D]8375 Communication parameter display [ch0]
[D]8376
[D]8377 Not used
[D]8378
360
Content of register
Y000] Current value register
Default: 0
[Y000] Maximum speed
Default: 100000
[Y000] Zero return speed
Default: 50000
[Y001] Current value register
Default: 0
[Y001] Maximum speed
Default: 100000
[Y001] Zero return speed
Default: 50000
[Y002] Current value register
Default: 0
[Y002] Maximum speed
Default: 100000
[Y002] Zero return speed
Default: 50000
Appendix A-2 Special Data Register (D8000 to D8511)
Corres-
ponding Number and
special name
device
[D]8379
-
D 8380
-
D 8381
-
-
D 8382
- D 8383
[D]8384
-
[D]8385
-
[D]8386
-
[D]8387
-
[D]8388
[D]8389
-
Ring Counter
-
D 8398
D 8399
-
RS2 (FNC 87) [ch1]
-
D 8400
- [D]8401
*1
[D]8402
-
*1
[D]8403
-
[D]8404
-
[D]8405
[D]8406
-
[D]8407
- [D]8408
D 8409
-
D 8410
-
D 8411
-
D 8412
-
D 8413
-
[D]8414
M8372
[D]8415
M8373
[D]8416
-
[D]8417 to [D]8418 Not used
-
[D]8419
-
*1. Cleared when PLC switches from RUN to STOP.
- *2. 1ms ring counter (D8399, D8398) will operate after M8398
turns ON.
-
Appendix A: Special Device List
Content of register
RS2 (FNC 87) [ch0]
Time-out time setting
RS2 (FNC 87) [ch0]
Header 1 and 2 <Default: STX>
RS2 (FNC 87) [ch0]
Header 3 and 4
RS2 (FNC 87) [ch0]
Terminator 1 and 2 <Default: ETX>
RS2 (FNC 87) [ch0]
Terminator 3 and 4
RS2 (FNC 87) [ch0]
Receive sum (received data)
RS2 (FNC 87) [ch0]
Receive sum (calculated result)
RS2 (FNC 87) [ch0]
Receive sum (calculated result)
Not used
Operation mode display [ch0]
Up-operation ring counter of 0
Lower
to 2,147,483,647
Upper
(in units of 1ms, 32-bit)
RS2 (FNC 87) [ch1]
Communication format setting
Not used
RS2 (FNC 87) [ch1]
Remaining points of transmit data
RS2 (FNC 87) [ch1]
Monitoring receive data points
Not used
Communication parameter display [ch1]
Not used
RS2 (FNC 87) [ch1]
Time-out time setting
RS2 (FNC 87) [ch1]
Header 1 and 2 <Default: STX>
RS2 (FNC 87) [ch1]
Header 3 and 4
RS2 (FNC 87) [ch1]
Terminator 1 and 2 <Default: ETX>
RS2 (FNC 87) [ch1]
Terminator 3 and 4
RS2 (FNC 87) [ch1]
Receive sum (received data)
RS2 (FNC 87) [ch1]
Receive sum (calculated result)
RS2 (FNC 87) [ch1] Send sum
Operation mode display [ch1]
Corres-
ponding
special
device
-
-
-
-
-
-
-
-
-
-
-
M8398
*2
-
-
M8402
M8403
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-