10.10 Software Revision History - Rice Lake IQ PLUS 710 Installation Manual

TEST Menu
Function
CLEAR EEPROM Clear EEPROM
Read Caution! statement on page 76 before using this function.
Press and hold the setup switch, then press the
A/D OFFSET A/D offset calibration (–0.5 mv/V)
Read Caution! statement on page 76 before using this function. Press and hold the setup switch,
then press the 8 key to perform offset calibration.
A/D GAIN A/D gain calibration (+4.5 mv/V)
Read Caution! statement on page 76 before using this function. Press and hold the setup switch,
then press the 9 key to perform gain calibration.
EXIT Press the 3 key to exit test mode.

10.10 Software Revision History

The following list summarizes the principal software
changes made for Version 2.0:
Analog and Digital Filtering
¥ ConÞgurable analog Þlter added with available
settings of OFF, 2HZ, 8HZ.
¥ Digital Þltering changed from one to two Þlters
(DIGFLT1 and DIGFLT2). New RATTRAP
parameter enables RATTLETRAP
for both digital Þlters.
Serial Communications and Printing
¥ PORT parameters removed from the SERIAL
menu.
¥ EDP port AB-RIO parameter name changed to
BUS; BUS parameter added to printer port.
¥ Printer port now supports duplex RS-232
communications; can be used to send and
receive EDP commands.
¥ Streamed weight information now uses the
following units designators: lb=L; Kg=K; oz=O;
gram=G; ton, metric ton, and long ton=T; grain,
troy ounce, troy pound, and none=space.
¥ Print command latches for three seconds: A
print command issued while the scale is in
motion is now completed if the scale comes out
of motion before the three seconds elapses.
¥ CONSNUM (consecutive numbering) and UID
(unit ID) parameters added to PROGRM menu.
Zero and Tare Operations
¥ Except in OIML mode, a tare is cleared by
pressing the
TARE
NTEP, CANADA, and OIML modes all require
the scale to be at no load before clearing a tare.
¥ Scale can now be zeroed (gross zero) with a tare
remaining in the system. Exception: In OIML
Table 10-7. Test Menu Functions (Continued)
¨
algorithm
(rather than ) key.
ZERO
Description
.
(decimal_point) key to clear EEPROM.
mode, the tare is cleared when the
pressed.
¥ Tare values restricted to six digits to avoid
display overßow when tare weight is removed.
See the listings under ÒTruck ModeÓ for more
tare-related changes.
Truck Mode
¥ In truck mode, you can now clear individual tare
values or the entire tare register.
¥ The word
TARE
TARE100 truck mode storage register printouts
to prevent labeling of stored weights as tare
weights.
¥ Truck mode tare storage register increased to
300 IDs.
¥ The truck mode storage register can now be
called up by pressing the
Setpoints
¥ The IQ plus 710 now supports up to 20
setpoints, including all setpoint kinds available
for the IQ plus 800/810 indicators.
¥ SETPNTS menu name changed to SETPTS.
¥ SPNAMES parameter has been removed from
SETPTS menu. A name can now be selected (for
any setpoint kind) from a list of up to 60
prompts deÞned on the PROGRM menu,
PROMPTS parameter.
¥ All setpoint kinds now default to ACCESS=ON.
Batching Operations
¥ Setpoint name can be displayed while a batch is
running.
¥ PREACT and BANDVAL values can be entered
at the front panel.
key is
ZERO
has been removed from
ID key.
Appendix 77