GE 469 Instruction Manual page 212

6.3 MEMORY MAP
Table 6–2: MEMORY MAP DATA FORMATS (Sheet 9 of 12)
FORMAT TYPE DEFINITION
CODE
76 RTD 12 Alarm
77 Open RTD Alarm
78 Short/Low RTD Alarm
79 Undervoltage Alarm
80 Overvoltage Alarm
81 Volt. Frequency Alarm
82 Power Factor Alarm
83 Reactive Power Alarm
84 Underpower Alarm
85 Trip Counter Alarm
86 Starter Failed Alarm
87 Current Demand Alarm
88 kW Demand Alarm
89 kvar Demand Alarm
90 kVA Demand Alarm
91 Broken Rotor Bar
92 Analog I/P 1 Alarm
93 Analog I/P 2 Alarm
94 Analog I/P 3 Alarm
95 Analog I/P 4 Alarm
96 Reverse Power Alarm
97 Incomplete Sequence Alarm
98 Analog Differential 1-2 Alarm
99 Analog Differential 3-4 Alarm
Ø
101 Service Alarm
102 Control Power Lost
6
103 Cont. Power Applied
104 Emergency Rst. Close
105 Emergency Rst. Open
106 Start While Blocked
107 Relay Not Inserted
108 Trip Coil Super.
109 Breaker Failure
110 Welded Contactor
111 Simulation Started
112 Simulation Stopped
Ø
118 Digital Trace Trigger
119 Serial Trace Trigger
120 RTD 1 High Alarm
121 RTD 2 High Alarm
122 RTD 3 High Alarm
123 RTD 4 High Alarm
124 RTD 5 High Alarm
125 RTD 6 High Alarm
126 RTD 7 High Alarm
127 RTD 8 High Alarm
128 RTD 9 High Alarm
129 RTD 10 High Alarm
130 RTD 11 High Alarm
131 RTD 12 High Alarm
132 Overtorque Alarm
6-50
Courtesy of NationalSwitchgear.com
Ø
Ø
469 Motor Management Relay
Table 6–2: MEMORY MAP DATA FORMATS (Sheet 10 of 12)
FORMAT TYPE DEFINITION
CODE
133 R1 Relay Forced
134 R2 Relay Forced
135 R3 Relay Forced
136 R4 Relay Forced
137 R5 Relay Forced
138 Force R1 Disabled
139 Force R2 Disabled
140 Force R3 Disabled
141 Force R4 Disabled
142 Force R5 Disabled
143 Motor Started
FC135 Unsigned MOTOR SPEED
16 bit integer
0 Low Speed (Speed 1)
1 High Speed (Speed 2)
FC136 Unsigned ORDER CODE
16 bit integer
Bit 0 0 - Code P5 (5A phase CT),
1 - Code P1 (1A phase CT)
Bit 1 0 - Code HI (High Voltage Power Supply),
1 - Code LO (Low Voltage Power Supply)
Bit 2 0 - Code A20 (4-20 mA Analog Outputs),
1 - Code A1 (0-1 mA Analog Outputs)
FC137 Unsigned CONTROL RELAYS FOR REDUCED
16 bit integer VOLTAGE STARTING
0 Auxiliary 2
1 Auxiliary 2 & Auxiliary 3
2 Auxiliary 3
FC138 Unsigned SIMULATION MODE
16 bit integer
0 Off
1 Simulate Pre-Fault
2 Simulate Fault
3 Pre-Fault to Fault
FC139 Unsigned FORCE OPERATION OF RELAYS
16 bit integer
0 Disabled
1 R1 Trip
2 R2 Auxiliary
3 R3 Auxiliary
4 R4 Alarm
5 R5 Block Start
6 R6 Service
7 All Relays
8 No Relays
FC140 Unsigned GENERAL STATUS
16 bit integer
bit 0 Relay in Service
bit 1 Active Trip Condition
bit 2 Active Alarm Condition
bit 3 Reserved
bit 4 Reserved
bit 5 Reserved
bit 6 Reserved
bit 7 Reserved
bit 8 Motor Stopped
6 COMMUNICATIONS
GE Multilin