Parameter Table - YASKAWA CIMR-AC2B0004 Quick Start Manual

7

Parameter Table

This parameter table shows the most important parameters.
Default settings are bold type. Refer to the Technical
Manual for a complete list of parameters.
No. Name
Initialization Parameters
0: View and set A1-01 and A1-04. U -
parameters can also be viewed.
1: User Parameters (access to a set of
Access Level
A1-01 parameters selected by the user, A2-01 to
Selection
A2-32)
2: Advanced Access (access to view and
set all parameters)
Control
0: V/f Control
A1-02 Method
5: Open Loop Vector Control for PM
Selection
0: No initialization
1110: User Initialize (parameter values must
Initialize be stored using parameter o2-03)
A1-03
Parameters 2220: 2-wire initialization
3330: 3-wire initialization
5550: oPE04 error reset
Operation Mode Selection
0: Digital operator
Frequency 1: Analog input terminals
b1-01 Reference 2: MEMOBUS/Modbus communications
Selection 1 3: Option PCB
4: Pulse input (terminal RP)
0: Digital operator
Run
1: Digital input terminals
b1-02 Command
2: MEMOBUS/Modbus communications
Selection 1
3: Option PCB
0: Ramp to stop
Stopping 1: Coast to stop
b1-03 Method 2: DC Injection Braking to stop
Selection 3: Coast with timer
9: Simple Positioning Stop
Reverse
0: Reverse enabled.
b1-04 Operation
1: Reverse disabled.
Selection
0: Standard
Phase Order
b1-14 1: Switch phase order (reverses the direction
Selection
of the motor)
DC Injection Braking
DC Injection Sets the frequency at which DC Injection
b2-01 Braking Start Braking starts when "Ramp to stop" (b1-03
Frequency = 0) is selected.
DC Injection
Sets the DC Injection Braking current as a
b2-02 Braking
percentage of the drive rated current.
Current
DC Injection Sets DC Injection Braking (Zero Speed
b2-03 Braking Time Control when in CLV/PM) time at start.
at Start Disabled when set to 0.00 seconds.
DC Injection
b2-04 Braking Time Sets DC Injection Braking time at stop.
at Stop
Acceleration/ Deceleration
Acceleration Sets the time to accelerate from 0 to
C1-01
Time 1 maximum frequency.
YASKAWA ELECTRIC TOEP C710606 48A - AC Drive A1000 1000Hz Software - Quick Start Guide
Description
No. Name
Deceleration Sets the time to decelerate from maximum
C1-02
Time 1 frequency to 0.
Acceleration/
C1-03 to Set the accel/decel times 2 to 4 (set like C1-
Deceleration
C1-08 01/02).
Time 2 to 4
S-Curve
C2-01 Characteristic S-curve at acceleration start.
at Accel Start
S-Curve
C2-02 Characteristic S-curve at acceleration end.
at Accel End
S-Curve
C2-03 Characteristic S-curve at deceleration start.
at Decel Start
S-Curve
C2-04 Characteristic S-curve at deceleration end.
at Decel End
Slip Compensation
Slip
Sets the gain for the motor slip
C3-01 Compensation
compensation function used for motor 1.
Gain
Slip
Compensation Adjusts the slip compensation function
C3-02
Primary Delay delay time used for motor 1.
Time
Torque Compensation
Sets the gain for the automatic torque
Torque
(voltage) boost function and helps to
C4-01 Compensation
produce better starting torque. Used for
Gain
motor 1.
Torque
Compensation
C4-02 Sets the torque compensation filter time.
Primary Delay
Time
Carrier Frequency
Carrier
C6-03 Frequency 1.1 ~ 12.5kHz
Max
Frequency Reference
Frequency Sets the frequency reference for the drive.
d1-01 to
Reference Setting units are determined by parameter
d1-16
1 to 16 o1-03.
Jog Frequency Sets the Jog frequency reference. Setting
d1-17
Reference units are determined by parameter o1-03.
V/f Pattern for Motor 1
This parameter must be set to the power
supply voltage.
WARNING! Drive input voltage (not motor
Input Voltage voltage) must be set in E1-01 for the
E1-01
Setting protective features of the drive to function
properly. Failure to do so may result in
equipment damage and/or death or personal
injury.
7 Parameter Table
Description
EN 29