Piazzetta IP 78/68 Instructions For Installation, Use And Maintenance Manual page 48

The operating principle is as follows:
When the room temperature measured by the remote control or the stove reaches the temperature value programmed by the user, the stove
automatically goes to power level 1 (readout "OK" on the display).
If the room temperature continues to rise with operation at power level 1 up to the value set on the STOP function (e.g. + 2°C compared to the
programmed temperature), the stove shuts down and goes into the stand-by mode.
When the room temperature measured by the remote control or the stove drops to the temperature value set by the user on the START function (e.g.
- 3°C compared to the programmed temperature), the stoves starts a new ignition phase and goes back to the power level previously set by the user.
a
The stove only starts up again when the temperatures measured on the actual appliance allow it to be used in all safety.
If the STOP function is OFF, upon reaching the programmed room temperature, the stove will operate in the conventional way by going to power level
1 without shutting down.
Similarly, if the START function is OFF, the stove does not start the ignition phase after automatic shutdown but remains shut down.
If you have set the ENERGY SAVING mode, the timer mode will manage only the starts and the stops of the programmed timeslots.
a
This function cannot be handled by the external thermostat, but only from the supplied remote control.
Function
Select the ENERGY Press the MENU key, then using the SELECT MENU key select the ENERGY
SAVING menu SAVING function and confirm by pressing the SET key.
Press the SELECT MENU key and then select the temperature set point
Select the value to
between 1 and 3 or disable the function by selecting OFF.
be set for shutdown
temperature
Confirm by pressing the SET key.
Press the SELECT MENU key and then select the temperature set point
Select the value to
between 1 and 3 or disable the function by selecting OFF.
be set for ignition
temperature
Confirm by pressing the SET key.
After confirmation using the SET key, the readout FUNTION ENABLED is
displayed and the readout ENS (ENERGY SAVING) appears on the main
display.
Upon reaching the temperature set in the STOP function, the stove starts
the shutdown stage.
The readout ENERGY SAVING OK appears on the display.
48
ENERGY SAVING
Action
H07028420 / DT2000990 – 01
E N E R G Y
Display
E N E R G Y
S A V I N G
E N E R G Y
S A V I N G
E N E R G Y
S A V I N G
E N E R G Y
S A V I N G
1
S A V I N G
1
1
1
S T O P
1
S T O P
S T O P
S T O P
. c
1
S T O P
. c
1
1
. c
1
1 . c
1
. c
1
1
1
S T A R T
1
S T A R T
S T A R T
S T A R T
O F F
S T A R T
O F F
1
O F F
1
O F F
1
O F F
1
L E V E L
1
L E V E L
E N S P 2
L E V E L
E N S P 2
L E V E L
. c
E N S P 2
1 2 : 0 0 2 2
L E V E L
. c
E N S P 2
1 2 : 0 0 2 2
1 .
E N S P 2
1 2 : 0 0 2 2
c
. c
1
1 2 : 0 0 2 2
1 . c
1 2 : 0 0 2 2
1
E N E R G Y
1
E N E R G Y
S A V I N G O K
E N E R G Y
S A V I N G O K
E N E R G Y
. c
S A V I N G O K
1 2 : 0 0 2 2
E N E R G Y
. c
S A V I N G O K
1 2 : 0 0 2 2
1
. c
S A V I N G O K
1 2 : 0 0 2 2
DT2040104-00
.
1
1 2 : 0 0 2 2
c
. c
1
1 2 : 0 0 2 2
1
1