Programming A Relay Broadcast Initiation - Muratec MFX-1500 Operating Instructions Manual

5. Use the numeric keypad to enter the number exactly as your machine
should dial it, including whatever codes your phone system may require.
The number can be up to 40 characters in length:
78:Fax Number
9-5558422_
Your display can show only 20 characters at a time. To view characters
beyond those 20 (such as with an international long-distance numbers),
press to scroll leftward or
Important: Do not press
ENTER
Note: If you make a mistake or want to erase characters entered in a
previous setting, press
CANCEL
to change just one character in the number, press
cursor leftward, or to move it rightward, to that character and
press to erase it. Then re-enter until the number is just as
CANCEL
you want it.
6. Now, while you still can see the fax number on the display, press
two times and then press
COMMUNICATION OPTIONS
display shows:
S Mail Tx
S Mail No. _
7.
Use the numeric keypad to enter the appropriate one-digit SecureMail
mailbox number. In this example, the number is 5.
S Mail Tx
S Mail No. 5_
When the entry is complete, press
8.
If you want the transmission to begin immediately every time you press
the key, press again and skip to step 11.
ENTER
If you want to delay the transmission (perhaps to take advantage of lower
phone rates), press
COMMUNICATION OPTIONS
9.
There's a choice to make. Instruct your fax to carry out this delayed
command in one of the following ways:
Option 1: Perform the command once at a certain time on a certain day of
the month (For example, "Do this at 5:05
To select this option, use the numeric keypad to enter the
date and time when the fax should perform the command:
Delayed
Enter Time: 30/17:05
to scroll rightward.
.
to erase leftward. Or, if you want
to move the
. The
ENTER
.
ENTER
, .
ENTER
on the 30th.")
PM
Option 2: Perform the command at a certain time each day you press
the key. (For example, "Do this at 5:05
To select this option, use the numeric keypad to enter 0, 0
(i. e., 00), and then the time when the fax could perform
the command:
Delayed
Enter Time: 00/17:05
10. Press , .
ENTER ENTER
11.
The display now shows the next programmable one-touch key.
If you do not wish to enter or change any other key's programming, press
to return your machine to its usual standby mode.
STOP
If you do wish to enter or change this key's programming, go back to step 3.
If you wish to enter or change another key's programming, go back to
step 2.

Programming a relay broadcast initiation

Note: To erase a programmable one-touch key, refer to page 2.70.
Note: For this operation to work, three things must be true:
The remote fax machine must be a Muratec fax machine (other than
an F-86) with "hub" capability.
The call group(s) to which you're faxing must exist on the
remote machine.
You must know the two-digit mailbox number for each call group to
which you're faxing.
To program a relay broadcast initiation into a programmable one-touch key:
1.
Change to the Fax mode then press
either shows:
Select Program No.
73:No Number Stored
. . . or indicates a command already is programmed into this key.
If 73 is the key you want to program, skip to step 4. (However, our
examples from here will say "77" rather than "73. "
2.
Select the key in which you want to program a command or change a
previously stored command — if necessary, turn the fliptab to see it, as
described earlier — and then press it. Here, we've selected 77.
Select Program No.
77:No Number Stored
Beyond the bas cs
today.")
PM
, , 1, . The display
PROGRAM C ENTER
2.63