Timers (General) - GRAUPNER mx-20 Hott Programming Manual

Timers (general)

Timers on the basic display
The default transmitter display shows a total of three
timers. These are: the transmitter operating time on the
left of the display, plus a "Top" and a "Centr" timer on the
right of the display:
GRAUBELE Stop
#01 Flt
5.9V
K78
0:00h M
A further, fl ight-phase specifi c timer can also be
confi gured, depending on your settings in the two menus
"Fl. phase timers" (page 142) and "Phase settings"
(pages 128 and 132). This optional fl ight phase timer
– such as the lap time timer – appears underneath the
"Centr" (fl ight time) timer:
GRAUBELE Stop
#01 Flt
«Speed » Lap
5.2V
K78
2:22h M
To confi gure the "Top" and/or "Centr" timer, use the
arrow keys on the left or right touch pad to access the
menu option "Timers (general)" in the multi-function list:
Non-delayed chan
Timers (general)
Fl. phase timers
Wing mixers
Free mixers
MIX active/phase
138 Detail program description - Control adjust
Non-delayed chan
Timers (general)
Fl. phase timers
Helicopter mixer
Free mixers
0:00
MIX active/phase
0:00
Tap the center SET
HoTT
the menu shown below:
0.0V
Model time
Batt. time
Top
Centr :
" Model time"
This timer shows the currently recorded total access
0:00
time to the currently active model memory. If necessary,
0:00
00 you can also infl uence the automated time recording
0:00.0
using a switch assigned at the right of the display, and
5.5V
use this switch to activate and deactivate the "Model
time" timer as required. This switch is assigned (and
erased again as required) as described in the section
"Assigning transmitter controls, switches and control
switches" on page 52.
Tapping the  or  keys on the right touch pad at
the same time (CLEAR) will reset the time to "0:00h".
" Batt. time"
This operating hours timer records the transmitter's
total switch-on time since the last time the battery was
charged, thus monitoring the transmitter battery. A
switch cannot be assigned to this function.
key on the right touch pad to open
12:34h –––
1:23h
: Stop 0:00
Flight 0:00
Timer
This timer is automatically reset to "0:00h" when the
transmitter detects that the voltage of the battery is
signifi cantly higher than the last time it was switched on,
e. g. as a result of a charge process or the installation of
a replacement battery.
Tapping the  or  keys on the right touch pad at
the same time (CLEAR) will also reset the time here to
"0:00h".
"Top" and "Centr"
These two timers are located at the top right of the basic
display (see the screen image immediately to the left)
and can be assigned a different name; their function and
mode of operation varies according to the name you
give them. Independently of the name each is given,
the "Top" and "Centr" timer can be programmed to run
any length of time forwards or backwards – see further
below.
Using the arrow keys on the left or right touch pad,
select the line for the "Top" or "Centr" timer. Tap the
center SET key on the right touch pad briefl y to activate
the selection of a timer type:
Model time 12:34h
Batt. time 1:23h
Top : Stop
Centr :Flight
SEL
Now use the arrow keys on the left or right touch pad to
select your desired timer and complete your selection
by once again tapping the center SET
touch pad:
–––
0:00
0:00
Timer
key on the right